manualshive.com logo in svg

D-Link DAP-1360, User Manual

Share
Download
D-Link DAP-1360 User Manual Download Page 188

DAP-1360

 Wireless N300 Access Point & Router

User Manual

Configuring Device (Router Mode)

Creating Dynamic IP + PPPoE WAN Connection

To create a connection of the Dynamic IP + PPPoE type, click the 

Add 

button on the 

Net / WAN

page. On the opened page, select the

 Dynamic IP + PPPoE

 value from the 

Connection Type

drop-down list and specify the needed values.

Figure 151. The page for creating a new connection. The 

General settings

 section.

Parameter

Description

General settings

Interface

A physical interface to which the new connection will be assigned.

Name

A name for connection for easier identification.

Enable

Select the checkbox to enable the connection.

Direction

The direction of this connection.

Page 

188

 of 270

Summary of Contents for DAP-1360















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands