Cypress PSoC CY8C23533 Technical Reference Manual Download Page 59 | Manualshive

Page: 59 / 410

Cypress PSoC CY8C23533 Technical Reference Manual Download Page 59

Document # 001-20559 Rev. *D

59

RAM Paging

4.2.2

CPU_F Register

The M8C Flag Register (CPU_F) provides read access to
the M8C flags.

Bits 7 and 6: PgMode[1:0].

PgMode determines how the

CUR_PP and IDX_PP registers form effective RAM
addresses for Direct Address mode and Indexed Address
mode operands.

Bit 4: XIO.

The IO Bank Select bit, also know as the regis-

ter bank select bit, is used to select the register bank that is
active for a register read or write. This bit allows the PSoC
device to have 512 8-bit registers and, therefore, can be
thought of as the ninth address bit for registers. The address
space accessed when the XIO bit is set to ‘0’ is called the

, while the address space accessed when the

XIO bit is set to ‘1’ is called the

configuration space

.

Bit 2: Carry.

The Carry Flag bit is set or cleared in

response to the result of several instructions. It can also be
manipulated by the flag-logic opcodes (for example, OR F,
4). See the

PSoC Designer Assembly Guide User Manual

for more details.

Bit 1: Zero.

The Zero Flag bit is set or cleared in response

to the result of several instructions. It can also be manipu-
lated by the flag-logic opcodes (for example, OR F, 2). See
the

PSoC Designer Assembly Guide User Manual

for more

details.

Bit 0: GIE.

The state of the Global Interrupt Enable bit

determines whether interrupts (by way of the IRQ) are rec-
ognized by the M8C. This bit is set or cleared by the user,
using the flag-logic instructions (for example, OR F, 1). GIE
is also cleared automatically by the M8C upon entering the
ISR, after the flag byte has been stored on the stack, pre-
venting nested interrupts. Note that the bit can be set in an
ISR if desired. For GIE=1, the M8C samples the IRQ input
for each instruction. For GIE=0, the M8C ignores the IRQ.

For additional information, refer to the

CPU_F register on

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

x,F7h

PgMode[1:0]

XIO

Carry

Zero

GIE

RL : 02

LEGEND

L

The AND F, expr; OR F, expr; and XOR F, expr flag instructions can be used to modify this register.

x

An ‘x’ before the comma in the address field indicates that this register can be read or written to no matter what bank is used.

«
...
57
58
59
60
61
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands