Cypress PSoC CY8C23533 Technical Reference Manual Download | Manualshive

Page: 41 / 410

background image

Document # 001-20559 Rev. *D

41

CPU Core (M8C)

2.6.4

Destination Direct

For these instructions, the destination address is stored in the machine code of the instruction. The source for the operation is
either the M8C A or X register as indicated by the instruction’s opcode. All instructions using the Destination Direct address-
ing mode are two bytes in length.

Destination Direct Examples:

2.6.5

Destination Indexed

For these instructions, the destination offset from the X register is stored in the machine code for the instruction. The source
for the operation is either the M8C A register or an immediate value as indicated by the instruction’s opcode. All instructions
using the Destination Indexed addressing mode are two bytes in length.

Destination Indexed Example:

2.6.6

Destination Direct Source Immediate

For these instructions, the destination address is stored in operand 1 of the instruction. The source value is stored in operand
2 of the instruction. All instructions using the Destination Direct Source Immediate addressing mode are three bytes in length.

Destination Direct Source Immediate Examples:

Table 2-9. Destination Direct

Opcode

Operand 1

Instruction

Destination Address

Source Code

Machine Code

Comments

ADD

[7], A

04 07

The value in the Accumulator is added to memory at address 7. The
result is placed in memory at address 7. The Accumulator is unchanged.

MOV

REG[8], A

60 08

The Accumulator value is moved to register space at address 8. The
Accumulator is unchanged.

Table 2-10. Destination Indexed

Opcode

Operand 1

Instruction

Destination Index

Source Code

Machine Code

Comments

ADD

[X+7], A

05 07

The value in memory at address X+7 is added to the Accumulator. The
result is placed in memory at address X+7. The Accumulator is
unchanged.

Table 2-11. Destination Direct Source Immediate

Opcode

Operand 1

Operand 2

Instruction

Destination Address

Immediate Value

Source Code

Machine Code

Comments

ADD

[7], 5

06 07 05

The value in memory at address 7 is added to the immediate value 5. The
result is placed in memory at address 7.

MOV

REG[8], 6

62 08 06

The immediate value 6 is moved to register space at address 8.

«
...
39
40
41
42
43
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

Brand: abaco systems Pages: 88

Brand: VDO Pages: 22

Brand: PEP Pages: 120

MightyBoard 800

Brand: Ampro Pages: 26

486E P/N 5001561 Revision A

Brand: Ampro Pages: 118

Little Board/PLUS

Brand: Ampro Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands