Cypress PSoC CY8C23533 Technical Reference Manual Download | Manualshive

Page: 203 / 410

background image

Document # 001-20559 Rev. *D

139

1,A8h

13.3.14

SARADC_TRS

SAR8 ADC Auto Align/Trigger Source Register

This register is where the ADC auto align/trigger source is set.

Select any digital blocks in digital ROW0 as the align/trigger source for ADC conversion. You can also select two adjacent
blocks in digital ROW0 as the align/trigger source for ADC conversion. For example, if there is one PWM8 UM in block DBB0x
and the system needs the ADC auto aligned with the PWM pulse, you can select the DBB0x as auto align/trigger source to
the ADC. Through setting the SARADC_TRCL register, you can trigger the ADC start conversion at any point during one
PWM cycle. You can also select two adjacent blocks as auto align/trigger source to align with a 16-bit PWM, timer, or counter.
Be sure that the block you select is the same block you place the user module that aligns with the ADC.

For additional information, refer to the

“Register Definitions” on page 266

in the SAR8 ADC Block chapter.

7:6

DCB03_HL[1:0]

Bit 7
0

DCB03 DR0 is not driving the channel high.

1

DCB03 DR0 is driving the channel high.

Bit 6
0

DCB03 DR0 is not driving the channel low.

1

DCB03 DR0 is driving the channel low.

5:4

DCB02_HL[1:0]

Bit 5
0

DCB02 DR0 is not driving the channel high.

1

DCB02 DR0 is driving the channel high.

Bit 4
0

DCB02 DR0 is not driving the channel low.

1

DCB02 DR0 is driving the channel low.

3:2

DBB01_HL[1:0]

Bit 3
0

DBB01 DR0 is not driving the channel high.

1

DBB01 DR0 is driving the channel high.

Bit 2
0

DBB01 DR0 is not driving the channel low.

1

DBB01 DR0 is driving the channel low.

1:0

DBB00_HL[1:0]

Bit 1
0

DBB00 DR0 is not driving the channel high.

1

DBB00 DR0 is driving the channel high.

Bit 0
0

DBB00 DR0 is not driving the channel low.

1

DBB00 DR0 is driving the channel low.

Note

The digital block with the smaller number has higher priority to output to the related channel.

The circuitry guarantees only the highest priority bit to be set to 1 when the user enables multiple
blocks to one channel. The user can see only one bit set for one channel if they read back the register
data.

Individual Register Names and Addresses:

1,A8h

SARADC_TRS : 1,A8h

7

6

5

4

3

2

1

0

Access : POR

RW : 00

RW : 00

RW : 00

RW : 00

Bit Name

DCB03_HL[1:0]

DCB02_HL[1:0]

DBB01_HL[1:0]

DBB00_HL[1:0]

Bits

Name

Description

«
...
201
202
203
204
205
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

Brand: Teknor Industrial Computers Pages: 204

Brand: VersaLogic Pages: 83

Brand: VersaLogic Pages: 89

Brand: Technologic Systems Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands