manualshive.com logo in svg

Cypress PSoC CY8C23533, Technical Reference Manual

The Cypress PSoC CY8C23533 is an innovative microcontroller product that offers advanced features for development projects. To get a comprehensive understanding of its capabilities, users can freely download the Technical Reference Manual from our website, ensuring they have the necessary information to maximize the potential of this remarkable device.

Share
Download
background image

Document # 001-20559 Rev. *D

123

1,00h

13.3

Bank 1 Registers 

The following registers are all in bank 1 and are listed in address order. Registers that are in both Bank 0 and Bank 1 are
listed in address order in the section titled 

“Bank 0 Registers” on page 49

.

13.3.1

PRTxDM0

Port Drive Mode Bit Register 0 

This register is one of three registers whose combined value determines the unique Drive mode of each bit in a GPIO port.

In register PRTxDM0 there are eight possible drive modes for each port pin. Three mode bits are required to select one of
these modes, and these three bits are spread into three different registers (PRTxDM0, 

“PRTxDM1” on page 124

, and

“PRTxDM2” on page 52

). The bit position of the effected port pin (for example, Pin[2] in Port 0) is the same as the bit position

of each of the three Drive Mode register bits that control the Drive mode for that pin (for example, Bit[2] in PRT0DM0, bit[2] in
PRT0DM1, and bit[2] in PRT0DM2). The three bits from the three registers are treated as a group. These are referred to as
DM2, DM1, and DM0, or together as DM[2:0]. 

All Drive mode bits are shown in the sub-table below ([21

0

] refers to the combination (in order) of bits in a given bit position);

however, this register only controls the 

least significant bit (LSb)

 of the Drive mode. 

For additional information, refer to the 

“Register Definitions” on page 8

 in the GPIO chapter. 

7:0

Drive Mode 0[7:0]

Bit 0 of the Drive mode, for each of 8-port pins, for a GPIO port.

[

21

0]

Pin Output High

Pin Output Low

Notes

00

0

b

Strong

Resistive

00

1

b

Strong

Strong

01

0

b

High Z

High Z

Digital input enabled.

01

1

b

Resistive

Strong

10

0

b

Slow + strong

High Z

10

1

b

Slow + strong

Slow + strong

11

0

b

High Z

High Z

Reset state. Digital input disabled for zero power.

11

1

b

High Z

Slow + strong

I2C Compatible mode.

Note

  A bold digit, in the table above, signifies that the digit is used in this register.

Individual Register Names and Addresses:

1,00h

PRT0DM0 : 1,00h

PRT1DM0 : 1,04h

PRT2DM0 : 1,08h

PRT3DM0 : 1,0Ch

7

6

5

4

3

2

1

0

Access : POR

RW : 00

Bit Name

Drive Mode 0[7:0]

Bit

Name

Description

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

Advantech PCM-3356 Startup Manual preview
PCM-3356
Brand: Advantech Pages: 5
Artesyn iVPX7225 RTM Quick Start Manual preview
iVPX7225 RTM
Brand: Artesyn Pages: 2
WinSystems LBC- 486Plus Operation Manual preview
LBC- 486Plus
Brand: WinSystems Pages: 98
IBASE Technology IB811F Series User Manual preview
IB811F Series
Brand: IBASE Technology Pages: 90
Emerson Motorola MVME197LE User Manual preview
Motorola MVME197LE
Brand: Emerson Pages: 80
VersaLogic Tetra VL-EPC-2700 Hardware Reference Manual preview
Tetra VL-EPC-2700
Brand: VersaLogic Pages: 28
VersaLogic Ocelot Reference Manual preview
Ocelot
Brand: VersaLogic Pages: 64

Brands by name

Popular brands

Load more brands