Cypress PSoC CY8C23533 Technical Reference Manual Download Page 185 | Manualshive

Page: 185 / 410

background image

Document # 001-20559 Rev. *D

121

x,FEh

13.2.69

CPU_SCR1

System Status and Control Register 1

This register is used to convey the status and control of events related to internal resets and watchdog reset.

In the table above, note that reserved bits are grayed table cells and are not described in the bit description section. Reserved
bits should always be written with a value of ‘0’. For additional information, refer to the

“Register Definitions” on page 51

in the

SROM chapter or

“Register Definitions” on page 23

of the External Crystal Oscillator (ECO) chapter.

Note

5. Bits 3 and 2 (ECO EXW and ECO EX, respectively) cannot be used by the CY8C27x43 for silicon revision A, and by the

CY8C24533, CY8C23533, CY8C23433, CY8C24633, CY8C24x23, and CY8C22x13 PSoC devices.

7

IRESS

This bit is read only.
0

Boot phase only executed once.

1

Boot phase occurred multiple times.

3

ECO EXW

ECO Exists Written.

1

The ECO Exists Written bit has been written with a ‘1’ or ‘0’ and is now locked.

0

The ECO Exists Written bit has never been written in User mode.

2

ECO EX

ECO Exists (write once – see the explanation in

“Register Definitions” on page 23

).

1

ECO operation exists (set/reset OSC_CR[7] to enable/disable).

0

ECO operation does not exist. 32 kHz clock source is locked to operate from the ILO.

0

IRAMDIS

0

SRAM is initialized to 00h after POR, XRES, and WDR.

1

Address 03h - D7h of SRAM Page 0 are not modified by WDR.

Individual Register Names and Addresses:

x,FEh

CPU_SCR1: x,FEh

7

6

5

4

3

2

1

0

Access : POR

R : 0

R : 0

RW : 0

RW : 0

Bit Name

IRESS

ECO EXW

ECO EX

IRAMDIS

Bit

Name

Description

«
...
183
184
185
186
187
...
»

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for PSoC CY8C23533

Brand: DFI Pages: 58

Brand: Radxa Pages: 9

Brand: Goodix Pages: 80

Brand: Data Modul Pages: 26

Brand: IBASE Technology Pages: 78

Brand: Vantron Pages: 68

COM Express PMC/XMC Ultra Lite Carrier

Brand: Connect Tech Pages: 28

SCP-P4040-4G-ENP2

Brand: SMART Pages: 2

Brand: NXP Semiconductors Pages: 16

Brand: NXP Semiconductors Pages: 21

Brand: Acrosser Technology Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands