manualshive.com logo in svg

Cypress EZ-USB CX3, Technical Reference Manual, Page: 21 / 35

Share
Download
Cypress EZ-USB CX3 Technical Reference Manual Download Page 21

 

Cypress EZ-USB CX3  

EZ-USB® CX3 Technical Reference Manual, Doc. No. 001-91492 Rev. *B 

21 

1.10.6   

CX3_CSI_SENSOR_SIG_EN (Register Address: 0x0010) 

This register enables or disables the output of the XSHUTDOWN and XRESET signals from the MIPI CSI-2 
block. 

This register is set by the 

CyU3PMipicsiInit()

 

and 

CyU3PMipicsiReset()

 

APIs. 

BIT 

15 

14 

13 

12 

11 

10 

9 

8 

NAME 

RESERVED 

BIT 

7 

6 

5 

4 

3 

2 

1 

0 

NAME 

RESERVED 

XSHUTDOWN ENABLE 

XRESET ENABLE 

RESERVED 

 

Register field 

Bit 

Description 

RESERVED 

[15:3] 

RESERVED. Firmware must preserve their settings by reading them, changing 
non-reserved bits, and re-writing them. 

XSHUTDOWN 
ENABLE 

[2] 

Enable MIPI CSI-2 XSHUTDOWN Signal:  

0: Enables the output for the MIPI CSI-2 XSHUTDOWN signal.  

1: Disables output for the MIPI CSI-2 XSHUTDOWN signal.  

The signal drive value is determined by 

CX3_CSI_SENSOR_SIG_VAL 

(Register Address: 0x0014)

 

[2]. 

XRESET ENABLE 

[1] 

Enable MIPI CSI-2 XRESET Signal:  

0: Enables the output for the MIPI CSI-2 XRESET signal.  

1: Disables the output for the MIPI CSI-2 XRESET signal.  

The signal drive value is determined by 

CX3_CSI_SENSOR_SIG_VAL 

(Register Address: 0x0014) 

[1]. 

RESERVED 

[0] 

RESERVED. Firmware must preserve their settings by reading them, changing 
non-reserved bits, and re-writing them. 

 

Summary of Contents for EZ-USB CX3




































Reviews:

No comments