manualshive.com logo in svg

Cypress enCoRe V CY7C643 Series, Technical Reference Manual

The Cypress enCoRe V CY7C643 Series is a versatile product known for its high performance and reliability. For in-depth information and guidance on using this product, be sure to download the free Technical Reference Manual available at manualshive.com. This manual provides detailed instructions and troubleshooting tips for this exceptional series.

Share
Download
background image

enCoRe™ V CY7C643xx, enCoRe™ V LV CY7C604xx TRM, Document No. 001-32519 Rev *H

204

0,E0h

21.3.38 INT_MSK0

Interrupt Mask Register 0 

This register enables the individual sources’ ability to create pending interrupts. 

When an interrupt is masked off, the mask bit is ‘0’. The interrupt continues to post in the interrupt controller. Clearing the
mask bit only prevents a posted interrupt from becoming a pending interrupt. For additional information, refer to the 

Register

Definitions on page 46

 in the Interrupt Controller chapter. 

7

I2C

0

Mask I2C interrupt.

1

Unmask I2C interrupt.

6

Sleep

0

Mask Sleep interrupt.

1

Unmask Sleep interrupt.

5

SPI

0

Mask SPI interrupt.

1

Unmask SPI interrupt.

4

GPIO

0

Mask GPIO interrupt.

1

Unmask GPIO interrupt.

3

Timer0

0

Mask Timer0 interrupt.

1

Unmask Timer0 interrupt.

0

V Monitor

0

Mask Voltage Monitor interrupt.

1

Unmask Voltage Monitor interrupt.

Individual Register Names and Addresses:

0,E0h

INT_MSK0 : 0,E0h

7

6

5

4

3

2

1

0

Access : POR

RW : 0

RW : 0

RW : 0

RW : 0

RW : 0

RW : 0

RW : 0

RW : 0

Bit Name

I2C

Sleep

SPI

GPIO

Timer0

Reserved

Reserved

V Monitor

Bit

Name

Description

Summary of Contents for enCoRe V CY7C643 Series


































































































































































































































































Reviews:

No comments

Related manuals for enCoRe V CY7C643 Series

Brands by name

Popular brands

Load more brands