Cypress CY8C28 series Technical Reference Manual Download Page 253 | Manualshive

Page: 253 / 571

background image

252

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

ACE_CMP_CR1

1,77h

13.3.32

ACE_CMP_CR1

Analog Type-E Comparator Bus 1 Register

This register is used to override the analog column comparator synchronization for analog columns 4 and 5.

By default, the analog comparator bus is synchronized by the column clock and driven to the digital comparator bus for use in
the digital array and the interrupt controller. The CLDIS bits are used to bypass the synchronization. This bypass mode can be
used in power down operation to wake the device out of sleep, as a result of an analog column interrupt.

Note that reserved bits are grayed table cells and are not described in the bit description section. Reserved bits should always
be written with a value of ‘0’. For additional information,

see “Register Definitions” on page 452

in the Two Column Limited

Analog System chapter.

5

CLDIS[5]

Controls the comparator output latch, column 5.
0

Comparator bus synchronization is enabled.

1

Comparator bus synchronization is disabled.

4

CLDIS[4]

Controls the comparator output latch, column 4.
0

Comparator bus synchronization is enabled.

1

Comparator bus synchronization is disabled.

Individual Register Names and Addresses:

1,77h

ACE_CMP_CR1: 1,77h

2L* Column

7

6

5

4

3

2

1

0

Access : POR

RW : 0

RW : 0

Bit Name

CLDIS[5

CLDIS[4]

* This register is only available for CY8C28xxx devices that have E-type analog blocks. This register is reserved for CY8C28x03, CY8C28x23, and CY8C28x43
devices.

Bits

Name

Description

«
...
251
252
253
254
255
...
»

Summary of Contents for CY8C28 series




























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CY8C28 series

Brand: L-Acoustics Pages: 20

Brand: Securi-Prod Pages: 3

Brand: Freescale Semiconductor Pages: 34

Brand: Matelec Pages: 2

Brand: Pro-face Pages: 48

Brand: SYCLOPE Pages: 28

Brand: YASKAWA Pages: 444

Brand: t.a.c. Pages: 8

Brand: Icom Pages: 23

Triton UltraLift

Brand: HydroHoist Pages: 9

Brand: YOKOGAWA Pages: 12

DeviceNet MSEL Series

Brand: IAI Pages: 144

Brand: Whadda Pages: 7

Brand: Adaptec Pages: 7

Brand: EMUS Pages: 36

Brand: Sloan Pages: 4

Brand: Ingersoll-Rand Pages: 8

Jetstream Classic

Brand: POSEIDON Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands