Cygnus M3-DIVE Operation Manual Download Page 9

Page: 9 / 117

Cygnus DIVE Operating Manual

M3-DIVE-M-ENG_Iss9.docx

Page 9 of 117

Gauge Kit Contents

The DIVE gauge is supplied as a complete kit in a tough Peli®
transportation case. Everything you need to begin taking thickness
measurements is included in the kit.

Cygnus DIVE Gauge Body and Wrist Strap

Ultrasonic Probe(s) with Coiled Cable

Two Rechargeable Batteries

Membrane Couplant, 25ml bottle

Battery Charger and Charger Base

AC Mains Lead for Battery Charger

Ultrasonic Couplant Gel (Blue), 100ml bottle

Test Block 15mm

(or ½”)

thick in Mild Steel

Spare Probe Membranes

10.

Membrane Key

11.

Silicone Grease, 50g tube

12.

USB Flash Drive with Documentation

13.

Calibration Certificate

14.

Operating Manual

With Data Logging Option and software

Summary of Contents for M3-DIVE






















































































































Search results

Summary of Contents for M3-DIVE

Reviews:

Related manuals for M3-DIVE

Brands by name

Popular brands

Cygnus M3-DIVE, Operation Manual

Search results

Summary of Contents for M3-DIVE

Reviews:

Related manuals for M3-DIVE

Brands by name

Popular brands