manualshive.com logo in svg

Cygnus M3-DIVE, Operation Manual, Page: 76 / 117

Share
Download
Cygnus M3-DIVE Operation Manual Download Page 76

Cygnus DIVE Operating Manual 

M3-DIVE-M-ENG_Iss9.docx 

 

Page 76 of 117 

The Lemo connector plugs into the 

top of the Topside Repeater Display 
unit. 
 
Align the red marks on the plug 
and socket. 

 

 
Remove the blanking plug from the 
spare connector on the DIVE 
gauge. 

 

The plug on the umbilical plugs into 
the socket on the DIVE gauge. 
 

 

Testing the Link 

Before use on a dive it is recommended to test the link between 
the DIVE gauge and the Topside Repeater (TSR) display unit. To 
do this simply power on both the TSR and the DIVE gauge then 
measure the test block 

–

 the TSR should display the same 

measurement as the gauge. 

Changing the Batteries 

The non-video overlay TSR operates from 2 x AA batteries. To 
change the batteries unscrew the round battery cover from the 
bottom of the TSR unit, the batteries can then be removed and 

replaced. When replacing the battery cover, screw only finger 
tight. 

Topside Repeater with Video Overlay 

The TSR is available with a Video Overlay function that will display 
the thickness measurement on a composite video signal, this 
allows the thickness measurement to be viewed on the topside 

monitor screen, and also recorded if video recording is being used. 
 

Summary of Contents for M3-DIVE






















































































































Reviews:

No comments