CYBEX CardioTouch 770T Service Manual Download Page 83 | Manualshive

Page: 83 / 261

background image

Error 5: Drive Communication Issue

Cause:

Loss of communication with the drive, the drive has not given a valid response in 350- 400ms.

Service:

Power outages are most suspect.

• Check the power cord, the power source (plug, outlet, cleanliness of power, brown-outs, etc.) and

internal communication cabling.

• If the drive controller shuts down communication while the display is powered up, it can store this

error.

• Check the communications cabling from the console to the motor controller.
• Check the motor connector at the motor controller. If the cable tie holding the cable is too tight it may

cause a loose connection. If so, snip the cable tie and secure the motor connection.

• If the data cable is routed alongside the cube or line filter it may flag unnecessary errors. Try to route

the cable closer to the frame away from the line filter.

• Can also occur if a 230V motor controller is accidentally installed in a 115V unit

Page 83 of 261

Cybex 770T/790T Treadmill Part Number

«
...
81
82
83
84
85
...
»

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Related manuals for CardioTouch 770T

Brand: YATEK Pages: 72

Brand: Rane Pages: 38

Brand: Kartsana Pages: 36

Brand: Nautilus Pages: 17

Brand: National Instruments Pages: 6

Brand: Omlet Pages: 2

Brand: Omicron Pages: 382

Brand: Omicron Pages: 188

Brand: Pari Pages: 282

Brand: GE Pages: 176

Brand: Triton Blue Pages: 11

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: REED Pages: 12

Brand: Garmat Pages: 13

Brand: Gama Sonic Pages: 4

Brand: ultraMEDIC Pages: 28

Brand: Evermed Pages: 16

Brand: Enerpac Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands