manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 116

Error 150: Out of SpeedRange (over 150hz)

Cause:

Target speed >150Hz. Console is either sending a false speed value, or the value or data transfer is
corrupt.

Service:

The display software is suspect. If this occurs, contact

Cybex Customer Service

immediately. The best

course of action is to upgrade the display software with the most up to date revision, either by replacing
the display board or upgrading the existing board.

Exit error log

Exit Set Up Mode by tapping the

Toolbox

icon, then tap the

Home

icon

. The screen will

refresh.

Software Update 770T

Software can ONLY be installed on the model it is designed for. Do NOT install this software on other
Arc Trainers, Bikes, or Treadmills.

Tools Required

• USB stick (CP-23199)
• Phillips screwdriver

Repairs and Service
• DO NOT load zip files onto USB stick
• Load un-zipped files onto USB stick
• DO NOT remove USB stick during upload procedure
• Power must remain on during upload procedure
• DO NOT press any keys on console during upload procedure

Prepare USB stick

1.

Plug USB stick into PC.

2.

Delete any files on USB stick.
Verify USB stick is blank.

3.

Go to the

LF World

service product pages for the latest software files or contact Cybex Customer

Service at 508-533-4300 to receive via email.

Page 116 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands