manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 107

Error 95: Low Voltage (DC Link)

Cause:

Input voltage drops to unacceptable limits:

• <200V for the 230V unit
• <85V for the 115V unit

Service:

Error 95 is caused by a power outage while the belt is moving, either on purpose (running the treadmill
to incline it, then shutting it off with the power switch) or by an outside influence (plug was kicked, loose
fitting outlet, power outage, circuit breaker tripped, or simply shutting of the power at the breaker).

• Verify the input voltage is correct for the controller used.
• Monitor input voltage for brown-outs and sags.
• Make sure the treadmill is on a dedicated circuit.

More than likely, power was interrupted during use and the treadmill itself has nothing wrong with it.

Page 107 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands