manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 77 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 77

 

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

70

2.3.9 Configure the Sensor Configuration Parameters

The door sensor (pins 5 and 6) on the header can be used to monitor a door's open or closed state. 
There is an option on the 

Sensor 

page to trigger on an open or short condition on these pins. The 

door sensor alarm will be activated when the 

Door Open Timeout

 parameter has been met.

The intrusion sensor is an optical sensor installed on the board and will be activated when the board 
is removed from the case.

Each sensor can trigger up to five different actions:

•

Flash the LED until the sensor is deactivated (roughly 10 times/second)

•

Activate the relay until the sensor is deactivated

•

Loop an audio file out of the speaker until the sensor is deactivated

•

Call an extension and establish two way audio

•

Call an extension and play a pre-recorded audio file

Note

Calling a preset extension can be set up as a point-to-point call, but currently can't send 
delayed DTMF tones.

1. Click 

Sensor 

menu button to open the 

Sensor 

page (

Figure 2-25

).

Summary of Contents for RAL 9003































































































































Reviews:

No comments