manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 66 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 66

 

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

59

Backup SIP User ID 2 

Specify the SIP User ID for the second backup SIP Server. This parameter 
becomes the user portion of the SIP-URI for the device's extension on the 
second backup SIP server. Enter up to 64 alphanumeric characters.

Backup SIP Auth ID 2 

Specify the Authenticate ID for the second backup SIP server. This 
parameter is required for SIP registration authentication. Enter up to 64 
alphanumeric characters.

Backup SIP Auth Password 2 

Specify the Authenticate Password for the second backup SIP server. This 
parameter is required for SIP registration authentication. Enter up to 64 
alphanumeric characters.

Remote SIP Port 

The Remote SIP Port is the port number the device will use as the 
destination port when sending SIP messages. The default Remote SIP 
Port is 5060. The supported range is 0-65536. Enter up to 5 digits.

Local SIP Port 

The Local SIP Port is the port number the device will use to receive SIP 
messages. The default Local SIP Port is 5060. The supported range is 0-
65536. Enter up to 5 digits.

Outbound Proxy 

Enter the Outbound Proxy address as an IPv4 address in dotted decimal 
notation or a fully qualified domain name (FQDN). When an IP address is 
configured, the device will send all SIP messages to this IP address. 
When an FQDN is configured, the device will run DNS NAPTR, SRV, and 
A queries on the FQDN to resolve an IP address to which it will send all 
SIP messages. This field can accept entries of up to 255 characters in 
length.

Outbound Proxy Port 

The Outbound Proxy Port is port number used as the destination port 
when sending SIP messages to the outbound proxy. A value of 0 will 
default to 5060. The supported range is 0-65536. Enter up to 5 digits.

Disable rport Discovery 

Disabling rport Discovery will prevent the device from including the public 
WAN IP address and port number in the contact information that is sent to 
the remote SIP servers. This will generally only need to be enabled when 
using an SBC or SIP ALG in conjunction with a remote SIP server.

Buffer SIP Calls 

Also referred to as delayed paging. Device will buffer up to 4 minutes of 
audio then play back the recording after hang up.

Re-registration Interval (in seconds) 

The SIP Re-registration interval (in seconds) is the SIP Registration lease 
time, also known as the expiry. The supported range is 30-3600 seconds. 
Enter up to 4 digits.

Unregister on Boot 

When enabled, the device will send one registration with an expiry of 0 on 
boot.

Keep Alive Period 

The minimum time in milliseconds between keep-alive packets sent for nat 
traversal. A value of 0 will disable keep alive packets.

SIP Strobe Settings

Blink Strobe on Ring 

When selected, the Strobe will blink a scene when ringing.

SIP Call Strobe Brightness 

How bright the strobe will blink when there is a SIP Call. This is the 
maximum brightness for “fade” type scenes.

ADA Compliant 

Strobe will blink ON at the specified brightness for 150ms then OFF for 
350ms during the duration of the event.

Slow Fade 

Strobe will increase in brightness from 0 to the specified brightness and 
back to 0 over the course of about 3.5 seconds during the duration of the 
event.

Table 2-13. SIP Configuration Parameters (continued)

Web Page Item

Description

Summary of Contents for RAL 9003































































































































Reviews:

No comments