manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 13 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 13

 Product Overview

Product Specifications

Operations Guide

931260A

CyberData Corporation

6

1.5 Product Specifications

Table 1-1. Product Specifications

Category Specification

Audio sensitivity

96dB/1W/1M S.P. Level

Audio output

10 Watts Peak Power

Operating temperature

-30 to 55 C (-22 to 131 F)

Ethernet port baud rate

10/100 Mbps

Protocol

InformaCast and/or SIP (RFC 3261)

Power Input (J1)

PoE 802.3af (as per IEEE 802.3af standard from a UL-listed, LPS-rated limited power source)

802.3at

44-57 VDC (48 VDC nominal) at 350mA

or Auxiliary Power Input

a

(Terminal Block J10)

12 VDC at 1A (from a UL-listed, LPS-rated power supply)

Total Power

~ 15W

Network Line loss

~ 2W

Total Pwr @ VoIP 
Speaker

~ 13W

Total available audio 
power

~ 10W

Idle PWR (losses/CPU)

~ 3W

Payload types

G.711 µ-law, G.711 a-law, and G.722

Warranty

2 years limited

Dimensions

9” x 2.4”

Weight

2.8 lbs./shipping weight of 3.8 lbs.

(1.3 kg/shipping weight of 1.7 kg)

Part number

011399*

, RAL 9002, Gray White, Standard Color

011400

, RAL 9003, Signal White, Optional Color

*Replaces 011182 and 011183.

a.Auxiliary power input for use when PoE power is not available. 12 VDC @ 1A. Do not use auxiliary power input 
when speaker J1 is connected to a PoE power source.

Summary of Contents for RAL 9003































































































































Reviews:

No comments