manualshive.com logo in svg

Cyber Power Mini Central CPSPV30000ETL Series, User Manual

Share
Download
Cyber Power Mini Central CPSPV30000ETL Series User Manual Download Page 34

     

User Manual                                                                              33 / 54                                                                      CPS Mini Central series 

 

P: output power of each phase 

Output Info

V: 232/ 233/ 232
I:27.6/27.5/27.6
P:6.17/6.41/6.40 

                                       

Power chart

Max:    26  kWh

 

 

Fig6.3.9 Interface 3: Output information     

 

Fig6.3.10 Interface 4: 24 hour’s generation curve 

 

Interface 4:

 24 hour’s generation curve. See Fig6.3.10 for reference. 

This interface shows the generated power of every hour this day. 

 

Max: maximum power of today 

 

Power curve: today’s power curve

 

 

6.3.2.3 Connecting messages 

 

When  inverter  started  to  connect  to  grid,  the  following  message  will  appear  on  LCD  screen.  See  Fig6.3.11  for 
reference.

 

 

State:Waiting
 Connect in 007S
E_today:  000kWh
E_all: 4532.2kWh

 

 

Fig6.3.11 Connect to gird interface 

6.3.2.4 LCD Lock and unlock 

LCD display will be locked while there is no any operation in two minutes. You need knock four times to unlock LCD. 
See Fig6.3.12 for reference.

 

 

State:Normal
  Power:  0.97KW
E_today:  000kWh
    LOCK

 

Fig6.3.12 Lock LCD display 

 

6.3.3 Operate by knock 

 

Knock type and definition 

The inverter can support four kinds of knock: single knock, double knock, thrice knock, Knock four times. Each kind 
of knock has different function. Refer to specified definition in Table 6.1. 

Table 6.1 Knock definition list 

Knock type 

Definition 

Single knock 

Down 

Double knock 

Enter 

Thrice knock 

Esc 

Knock four times 

Unlock LCD 

Light backlight and single knock to check running information 

 

Summary of Contents for Mini Central CPSPV30000ETL Series
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands