manualshive.com logo in svg

Cyber Power Mini Central CPSPV30000ETL Series, User Manual

Share
Download
Cyber Power Mini Central CPSPV30000ETL Series User Manual Download Page 19

     

User Manual                                                                              18 / 54                                                                      CPS Mini Central series 

5.3.2 Mounting Inverter 

 

 

Falling  equipment  can  cause  serious  or  even  fatal  injury,  never  mount  the  inverter  on  the 
bracket unless you are sure that the mounting frame is really firmly mounted on the wall after 
carefully checking.

 

 
After the bracket is firmly mounted on the wall, then mount the inverter on the bracket. 

 

Rise up the CPS Mini Central a little higher than the bracket. Considering the weight of CPS Mini Central, you 
need to hang on the inverter. During the process please maintain the balance of the CPS Mini Central. 

 

Hang  the  inverter  on  the  bracket  through the  match  hooks  on bracket  and the  back of  the  inverter.  Please 
reference in Fig5.5 

 

Installed one M6*10 screw at each side of inverter to reliable fixed it on the wall. Please reference in Fig 5.6. 

 

Connection of a second protective earthing conductor. Please reference in Fig5.7. 

 

Recommend  awning  installation,  the  purpose  is  to  extend  the  inverter  service  life  and  reduce  the  power 
derating of the inverter. The dimension of the awning refer to Fig5.8. 
 

    Fig 5.5

  Fig 5.6 

  Fig. 5.7 

Summary of Contents for Mini Central CPSPV30000ETL Series
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands