Custom Audio Electronics TG02H Command Manual Download Page 55

Page: 55 / 100

0x1B 0x61

<ESC a>

Select justification

Valid for

TG02H

[Format]

ASCII

ESC a

Hex

1B 61 n

Decimal

27 97 n

[Range]

0 ≤ n ≤ 2

48 ≤ n ≤ 50

[Description]

Aligns all data in one line to the specified position. n selects the type of justification as follows:

JUSTIFICATION

0, 48

Flush left

1, 49

Centered

2, 50

Flush right

[Notes]

• This command is only enabled when inserted at the beginning of a line.

• Lines are justified within the specified printing area.

• Spaces set by 0x09, 0x1B 0x24 and 0x1B 0x5C will be justified according to the previously-entered

mode.

[Default]

n = 0

[Reference]

[Example]

Flush left

Centered

Flush right

ABC

ABCD

ABCDE

ABC

ABCD

ABCDE

ABC

ABCD

ABCDE

ESC/POS™ emulation

│ 55

Summary of Contents for TG02H





































































































Search results

Summary of Contents for TG02H

Reviews:

Related manuals for TG02H

Brands by name

Popular brands

Custom Audio Electronics TG02H, Command Manual

Search results

Summary of Contents for TG02H

Reviews:

Related manuals for TG02H

Brands by name

Popular brands