12.5 Setup
It is possible to conigure the default parameters for device setup by editing the “Setup.ini” ile on the Flash Drive.
To enter the Flash Drive by iles sharing from Mass Storage, you need to enable the relative parameter during the con
-
iguration process (see chapter 5).
After editing device’s parameter, simply save the “Setup.ini” ile to make the modiies activated.
The “Setup.ini” ile is a coniguration ile that contains all the conigurable parameters listed in text format and divided into
some sections (indicated in square brackets).
The available values for every parameter, are listed after the parameter name. The value marked with the symbol ‘ * ’ is the
default one. To modify printer’s parameters, change the numeric value after the name of parameters. To set the parameter
to the default value, change the numeric value with the symbol D.
The “Setup.ini” ile permits the coniguration of the following parameters:
[PRINT]
Printer Emulation
0*, 1
0 = CUSTOM/POS
1 = SVELTA
Print Mode
0*, 1
0 = Normal
1 = Reverse
Autofeed
0*, 1
0 = CR disabled
1 = CR enable
Chars / inch
0, 1*, 2
0 = A=11 B=15 cpi
1 = A=15 B=20 cpi
2 = A=20 B=15 cpi
Code Table [num]
0
Chinese font
0*, 1
0 = Disabled
1 = Enabled
Speed / Quality
0, 1*, 2
0 = High Quality
1 = Normal
2 = High Speed
Paper Width
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,
11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24, 25, 26,
27, 28, 29, 30, 31*
0 = 18 mm
1 = 20 mm
2 = 22 mm
3 = 24 mm
4 = 26 mm
5 = 28 mm
6 = 30 mm
7 = 32 mm
8 = 34 mm
9 = 36 mm
10 = 38 mm
11 = 40 mm
12 = 42 mm
13 = 44 mm
14 = 46 mm
15 = 48 mm
16 = 50 mm
17 = 52 mm
18 = 54 mm
19 = 56 mm
20 = 58 mm
21 = 60 mm
22 = 62 mm
23 = 64 mm
24 = 66 mm
25 = 68 mm
26 = 70 mm
27 = 72 mm
28 = 74 mm
29 = 76 mm
30 = 78 mm
31 = 80 mm
Paper Threshold
0, 1*, 2, 3, 4, 5, 6
0 = 30 %
1 = 40 %
2 = 50 %
3 = 60 %
4 = 70 %
5 = 80 %
6 = 90 %
83
CUSTOM-Powered
Summary of Contents for STIMARE STIMA-SML
