Custom Audio Electronics P3 Page 37 User Manual Download

Page: 37 / 68

DHCP CLIENT

Setting of the DHCP protocol:

Disabled

protocol disabled

Enabled =

protocol enabled

This parameter is not printed on setup report and it is modiiable only during setup pro

cedure by software (see

paragraph 5.2

HOST NAME

Identiication name of the device.

This parameter is not printed on setup report and it is modiiable only during setup pro

cedure by software (see

paragraph 5.2

IP ADDRESS

IP address of the device.

This parameter is not printed on setup report and it is modiiable only during setup pro

cedure by software (see

paragraph 5.2

SUBNET MASK

This parameter identiies the local network address.

This parameter is not printed on setup report and it is modiiable only during setup pro

cedure by software (see

paragraph 5.2

DEFAULT GATEWAY

This parameter identiies the gateway IP address used to send applications to the external

network.

This parameter is not printed on setup report and it is modiiable only during setup pro

cedure by software (see

paragraph 5.2

TCP PORT

This parameter sets the TCP port number.

This parameter is not printed on setup report and it is modiiable only during setup pro

cedure by software (see

paragraph 5.2

MAC ADDRESS

This is the number, provided by the constructor, that identiies the device; this number

is univocal.

This parameter is not modiiable by setup.

Summary of Contents for P3





































































Search results

Summary of Contents for P3

Reviews:

Related manuals for P3

Brands by name

Popular brands

Custom Audio Electronics P3, User Manual

Search results

Summary of Contents for P3

Reviews:

Related manuals for P3

Brands by name

Popular brands