![background image](http://html1.mh-extra.com/html/curtis/tcc1n/tcc1n_service-manual_2699134001.webp)
1
NSF International requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine
can be moved for cleaning underneath.
2. This equipment is to be installed with adequate backflow protection to comply with applicable
federal, state and local codes..
3. Water pipe connections and fixtures directly connected to a potable water supply shall be sized,
installed and maintained in accordance with federal, state, and local codes.
Important Safeguards/Symbols
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance
should be performed by an authorized Wilbur Curtis service technician.
• Do NOT immerse the unit in water or any other liquid
• Never clean with scouring powders, bleach or harsh chemicals.
Symbols:
WARNINGS – To help avoid personal injury
Important Notes/Cautions
Sanitation Requirements
Curtis TCC1N Units are Factory Pre-Set and Ready to Go… Right From the Box.
Generally there will never be a reason to change factory settings. However, should you need to
make slight adjustments to meet your tea needs, adjustment instructions are provided later in this
manual.
System Requirements:
• Water Source 30 – 90 PSI (Minimum Flow Rate of
1
GPM). If incoming water supply is greater
than 90 PSI, additional regulation is required to meet the range.
• Water pipe connections and fixtures directly connected to a potable water supply shall be
sized, installed and maintained in accordance with federal, state, and local codes.
SETUP STEPS
The unit should be level (left to right and front to back), located on a solid counter top. Connect
a water line from the water filter to the
TCCN
tea dispenser. NOTE: Some type of water filtration
device must be used to maintain a trouble-free operation. (In areas with extremely hard water, we
suggest that a sedimentary and taste & odor filter be installed.) This will prolong the life of your
system and enhance tea quality.
INSTALLATION
1. Remove dispenser from carton.
2. Run a water line to the inlet fitting behind the dispenser. Flush the new water
-
line to remove foreign particles.
3. Connect a ¼” flared flexible or copper waterline to the male fitting on the back
of the dispenser.
4. Locate the water supply valve behind the unit to verify position is turned on.
CAUTION: We recommended that the water supply valve, behind unit, be turned off during
non-business hours.
Models Included
• TCC1N
• TCC2N
• TCC3N
NOTE: Water source
pressure must be a
minimum of 30 PSI
pressure at all times
to insure the quality of
the of the product.
5. Clean out the tea concentrate system before using the
TCCN
tea dispenser. Use a BIB (Bag-
in-Box) style cleaning solution to simplify the cleaning procedure. A cleaner like BevClean
beverage line cleaner comes in a 3 gallon bag-in-box that connects directly to your bag-in-box
system for line cleaning (http://bevclean.com).
a. Remove the quick disconnect from the tea concentrate bag.
b. Place the BIB cleaner container next to the ea dispenser. Pull the spout
from the cleaner box through the marked area. Remove the clear travel cap from
spout. Don’t worry about cleaner spilling when the cap is removed. The cap has
an internal seal.
c. Snap the QCD bag connector onto the bag spout.
OFF
ON
ISO 9001:2008 REGISTERED
WILBUR CURTIS CO., INC.
6913 West Acco Street
Montebello, CA 90640-5403
For the latest information go to
www.wilburcurtis.com
Tel: 800-421-6150
Fax: 323-837-2410
Technical Support: 1-800-995-0417 M-F 5:30am-4:00pm PT
Email: [email protected]
Service Manual – TCC1/2/3N
W
ilbur
C
urtis
C
ompany
, i
nC
.