Curtis Instruments 1212 Manual Download

Page: 22 / 52

3 — PROGRAMMABLE PARAMETERS

1212 & 1212P Manual - Sep 2019

Return to TOC

pg. 18

THROTTLE MENU

PARAMETER

ALLOWABLE RANGE

DESCRIPTION

Type

0–9

The 1212/1212P controller can accept inputs from both 5kΩ, 3-wire pot

throttles and voltage throttles. Set the throttle type parameter to match the

throttle used in your application.

5kΩ, 3-wire pot throttles

0 = wigwag
1 = inverted wigwag
2 = single-ended; neutral when wiper at PotLow
3 = inverted single-ended; neutral when wiper at PotHigh
4 = unipolar.

Voltage throttles

5 = wigwag
6 = inverted wigwag
7 = single-ended; neutral when wiper ≤ PotLow
8 = inverted single-ended voltage; neutral when wiper ≥ PotHigh
9 = unipolar

Note: If Throttle Type 5–9 is used, see note on

page 9

Neutral Input

On/Off

A vailable only with 1212P.

When programmed On, enables neutral input detection.

PotHigh

3–5 V

Sets the maximum voltage for voltage throttles (Types 5–9).
(For 5kΩ, 3-wire pot throttles, PotHigh is determined by the throttle itself.)

PotLow

0–2 V

Sets the minimum voltage for voltage throttles (Types 5–9).
(For 5kΩ, 3-wire pot throttles, PotLow is determined by the throttle itself.)

Neutral Deadband

5–30 %

Sets the throttle range the controller interprets as neutral. Increasing the

parameter setting increases the neutral range. This parameter allows the

neutral deadband to be defined wide enough to ensure the controller goes

into neutral when the throttle is released.
Guidelines for adjusting this parameter are provided in Section 5.

Throttle Max

40–100 %

Sets the pot wiper voltage required to produce 100% controller output.

Increasing the Throttle Max setting reduces the wiper voltage required, and

therefore reduces the stroke necessary to produce full output. This feature

allows reduced-range throttle assemblies to be used.
Guidelines for setting Throttle Max are provided in Section 5.

HPD

On/Off

When programmed On, vehicle drive is inhibited if a throttle command outside

the neutral deadband is issued before the controller is powered up. Drive

will continue to be inhibited until the throttle is returned to within the neutral

deadband. If the HPD fault is not cleared within 10 seconds, a wiring fault is

declared and a power cycle is required.

Summary of Contents for 1212





















































Search results

Summary of Contents for 1212

Reviews:

Related manuals for 1212

Brands by name

Popular brands

Curtis Instruments 1212, Manual

Search results

Summary of Contents for 1212

Reviews:

Related manuals for 1212

Brands by name

Popular brands