CUMMINS ALLISON JetCount 4020 Operating Instructions Manual Download Page 10

Page: 10 / 45

JetCount

Currency Counter

All Models

Direct Access Denomination Keys

Key Explanation

Key

Description

RESET

This key is used when clearing counts and restarts the machine after a stopping

condition.

DENSITY

This key is used for setting doubles detection sensitivity by denomination.

STRAP

This key is used for setting a Strap Limit at any preset value (5, 10, 20, 25, 50,

75, 100 or infinity). This key is also used to set strap values at levels other than

the preset values (i.e., 53, 79, etc.)

For models equipped with Magnetic SD (JetCount model 4021) or Magnetic and

UV/FL SD (JetCount model 4022), this key is used to activate suspect document

detection and set sensitivity by denomination.

SPEED

This key is used to set speed at

(low),

(medium) or

***

(high).

ADD

This key is used for accumulating a total even after notes have been removed

from the stacker. When disabled, totals clear each time the stacker is emptied.

DENOM

This key is used to select the denomination that will be used to count currency.

VALUE

This key is used to toggle between count and note values.

Strap

Density

Denomination

Add

$10

$20

$50

$100

Count

Speed

RESET DNSTY STRAP

SPEED

ADD

DENOM VALUE

Summary of Contents for JetCount 4020














































Search results

Summary of Contents for JetCount 4020

Reviews:

Related manuals for JetCount 4020

Brands by name

Popular brands

CUMMINS ALLISON JetCount 4020, Operating Instructions Manual

Search results

Summary of Contents for JetCount 4020

Reviews:

Related manuals for JetCount 4020

Brands by name

Popular brands