Cumberland PNEG-240 Installation And Operation Manual Download | Manualshive

Page: 13 / 76

background image

PNEG-240

Chain Feeding System

13

3. Calculating Weight, Load and Length

Calculating Weight of Suspended Hopper

For calculating the weight of the hopper to be suspended, identify the following components of the feed
system: (1) The type of hopper, (2) The type of hopper extension, (3) The type of gearbox (4) The type of
motor. Calculate the weight of the suspended hopper by inserting the weight (provided in the tables below)
for each component in the formula below.

H

(Weight of hopper with feed) +

W

(Weight of hopper extensions with feed) +

G

(Weight of gearboxe(s))

+

M

(Weight of motor(s) =

HW

(Hopper weight to be suspended)

H

+

W

+

G

+

M

=

HW

Weight of Hopper with Feed

Part #

Description

Lbs.

Kgs.

7100120

1 Line Unloader

73

32

C4920000-60

1 Line Mini Hopper

280

126

C4900000-60

1 Line Direct Drive Mini Hopper

280

126

07097525D

1 Line Fill Only Mini Hopper

136

126

C4920001-60

2 Line 1 Way Mini Hopper

343

155

C4900001-60

2 Line 1 Way Direct Drive Mini Hopper

353

160

C4900002-60

2 Line 2 Way Direct Drive Mini Hopper

474

215

C4920005-120

4 Line 2 Way Mini Hopper

668

303

C4900005-60

4 Line 2 Way Direct Drive Mini Hopper

659

299

7100784

Single Drive Unit with Gearbox and Motor

115

52

«
...
11
12
13
14
15
...
»

Summary of Contents for PNEG-240













































































Reviews:

No comments

Related manuals for PNEG-240

SACE Tmax XT Series

Brand: ABB Pages: 11

Brand: AcceleDent Pages: 3

Brand: Zero 88 Pages: 32

Brand: Eastern Jungle Gym Pages: 27

Brand: idi Pages: 20

Brand: G&G Pages: 2

Brand: H&S Pages: 46

Brand: ParaBody Pages: 6

Brand: ParaBody Pages: 11

Brand: Yamaha Pages: 126

DM 2000 Version 2

Brand: Yamaha Pages: 8

Brand: B medical systems Pages: 28

Brand: Maselec Pages: 6

Brand: LABORIE Pages: 116

Brand: Fisher Scientific Pages: 44

Brand: AGCO Pages: 44

Aesculap S4 FW103R

Brand: Braun Pages: 39

Brand: Heitronic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands