manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 89 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 89

G1 RO Parts Diagrams and Lists    

85

Cat. No. 01021713

Product Assembly

11.53 REF.

NOTE DIRECTION OF 

FLOW METER

4

2

1

3

5

6

7

Product from

Membrane Assy

Product Outlet

C

Figure 41. 

G1 Product Assembly.

For G1 2S, 3S, 4S, 2L, 3L, 4L

Item Part  No.

Description

Qty

01024512

Assembly, Product Flow Meter, G1

1

—

Nipple, 1/2"x5, PVC Sch. 80, TBE

1

2

01021033

Adapter Assembly, Flow Meter,  

1/2" NPT

1

3

—

Tee, 1/2", Threaded, PVC Sch. 80

1

4

—

1/2"-1/2" NPT Tube, Male Connector

2

5

01024516

Sensor, TDS, 24"L with 5 Pos Conn

1

6

01025827

Harness, Meter, 28" Long

1

7

01022706

Nozzle, Flow Meter

1

For G1 1F, 2F

Item Part  No.

Description

Qty

01024520

Assembly, Product Flow Meter, G1-1F, 

2F

1

—

Nipple, 1/2"x5, PVC Sch. 80, TBE

1

2

01021033

Adapter Assembly, Flow Meter,  

1/2” NPT

1

3

—

Tee, 1/2", Threaded, PVC Sch. 80

1

4

—

1/2"-1/2" NPT Tube, Male Connector

2

5

01024516

Sensor, TDS, 24"L with 5 Pos Conn

1

6

01025827

Harness, Meter, 28" Long

1

7

—

NOT USED

Summary of Contents for G1 Series















































































































































Reviews:

No comments