manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 61 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 61

Accessories    

57

Cat. No. 01021713

SV3 (Solenoid Valve) Mode/TDS Target

Solenoid valve SV3 is physically connected to the mini-aux board AUX4. When connected to AUX4, the TDS probe is set 

up as PRODUCT. 

NOTE  Unlike SV1 and SV2, which operate at line voltage (115VAC for G1, 230VAC for M2), SV3 must be a 24V 

solenoid valve such as P/N 01021310.

SV3 has three possible modes of operation: quality flush, permeate flush, and TDS target.

NOTE  Quality and Permeate Flush are disabled in TDS Target mode.

TDS Target

Target TDS: The RO system keeps track of the average product water TDS whenever the RO system is operating, mixing 

lower quality water with product water to meet the average product water TDS. The average TDS measurements of the 

RO product water are taken once per second, over an interval specified by the “TDS Target Time.”  The controller opens 

and closes valve SV3 every few seconds in order to produce product water with a TDS level near the programmed value.

Drain

Figure 34. 

Target TDS. 

For hardware, plumbing, and wiring details, order P/N 01025749 (Kit, Target TDS, 1-Series).

Summary of Contents for G1 Series















































































































































Reviews:

No comments