manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 47 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 47

Accessories    

43

Cat. No. 01021713

GBE-Wireless Communication Setup

Now set up the RO controller to communicate with the wireless remote.

RUNNING

JAN-01-12 12:01P

1.  From the default home screen, press  

. The screen displays the main menu.

 1) GO TO RUNNING

 2) GO TO OFFLINE

 3) INFORMATION 

>4) SETUP

2.  Press 

 

 

 to scroll to 4) SETUP.

3.  Press 

 to select the SETUP menu.

 2) LANGUAGE

 3) POWERON MODE 

 4) FLUSH MODES

>5) ACCESSORIES

4.  Press 

 

 

 

 

 to select 5)ACCESSORIES. The screen displays the ac-

cessories menu.

>1) WIRELESS REM

 2) MODEM

 3) FLOW METERS 

 4) SWITCH INPTS

5.  Press 

 

 

 

 

 to select 5)ACCESSORIES. The screen displays the ac-

cessories menu.

REMOTE DISPLAY

NOT INSTALLED

6.  Press 

  

 or 

 and then 

 to change the state to INSTALLED.

CHANNEL #

>1

7.  Press 

  

 or 

 and then 

 to select the channel number of the control valve. 

The CHANNEL # for the RO controller must be the same as the CHANNEL # for 

the Remote Display.

RF FREQUENCY 

915 Mhz

8.  Use this setting to select the correct radio frequency. Do not change the RF fre-

quency for North America installations..

RUNNING

JAN-01-12 12:01P

9.  Press 

 

 

 to save the settings and return to the home screen.

Summary of Contents for G1 Series















































































































































Reviews:

No comments