manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 29 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 29

First Time Setup    

25

Cat. No. 01021713

Flow Meter Settings

Screen Display

Range

Changing the Setting

FLOW METERS

INSTALLED

Installed

Not Installed

The screen displays the installation status of the flow meter. Press 

 

 

 to change the state to installed if a flow meter is in-

stalled in the RO system.

FM1 K FACTOR

80.0

0–9999

Press 

  

 or 

 and then 

 to change the K-Factor to the 

calculated value for the flow meter FM1 and/or FM2. 

RUNNING

JAN-01-12 12:01P

6.  Press 

 

 

 to save the settings and return to the home screen.

12.  Once all the desired flows are set, allow the system to run for approximately 30 minutes, and then record the 

following measurements using the units gauges (U), GROC information screens (G), and your instruments (I): 

a. Feed Flow Rate, gpm (G)
b. Feed Water Temperature, °F (I)
c. Feed Water SDI (I)
d. Feed TDS, ppm (I)
e. Inlet Pressure, psig (U)
f. System (pump outlet) pressure, psig (U)

 

g. Product TDS, ppm (G)
h. Product Flow, gpm (G)  

x TCF

1

 =

i. Product Temperature, °F (G)
j. Product Pressure, psig (I) 
k. Concentrate (waste) flow, gpm (a–h) 
l. % Recovery (see 

page 121

)

m. % Rejection (see 

page 121

)

1

TCF = Temperature Correction Factor. Refer to 

Table 2 on page 26 

for this value.

NOTICE 

The Global RO Controller has a feature which records historical data. The intial startup data is kept 

in the controllers memory. It is still a good idea to record the values on a separate sheet of paper 

and keep the data near the unit in case of electrical problems.

13.  Choose GO TO OFFLINE from the main menu. Connect the product tubing to the service plumbing.
14.  Test the operation of the pressure switch by closing the inlet water supply valve. The unit should shut off imme-

diately.

CAUTION!  If the unit does not shut off, turn the unit OFF immediately to prevent pump damage. 

Disconnect electrical power source, then check the wiring and replace the switch, if 

necessary.

15.  Open the inlet water supply valve. The unit should restart.
16.  If connected, test the storage tank level control shutdown and the pretreatment lockout function.

Summary of Contents for G1 Series















































































































































Reviews:

No comments