Culligan G1 Series Installation, Operation And Service Instructions Download Page 25

Page: 25 / 142

First Time Setup

Cat. No. 01021713

Other First Time Setup Settings

Screen Display

Range

Procedure

SET

DAY

1–31

1. The screen displays the day setting. Press

and

then

to change the value and see the next setting.

SET YEAR

2012

2010–2040

2. The screen displays the year setting. Press

and

then

to change the value and see the next setting.

CLOCK TYPE

12 HR

12 or 24

3. The screen displays the clock type setting. Press

and then

to change the value and see the next setting.

SET HOUR

12PM

12AM–11PM

4. The screen displays the hour setting. Press

and

then

to change the value and see the next setting.

SET

MINUTES

0–59

5. The screen displays the minutes setting. Press

and then

to change the value and see the next setting.

POWERON MODE

OFFLINE

Running

Offline

6. The screen displays the selected status of the RO when pow-

ered on. Press

and then

to change the val-

ue and see the next setting.

SYSTEM UNITS

US INCH

METRIC

7. The screen displays the units of measure setting. Press

and then

to change the value and complete the

first-time setup.

NOTE This setting does not automatically change to metric

if you select a language other than English.

Completed First Time Setup

STARTING

JAN-01-12 12:01P

1. When the setup is complete, the circuit board microprocessor automatically calcu-

lates the water conditioner capacity. The screen displays the initializing status and

the current date and time, and then transitions to the home screen.

RUNNING

JAN-01-12 12:01P

2. The screen displays the current state of the RO system (RUNNING or OFFLINE)

and the date/time set for the unit. This is the default home screen.

Summary of Contents for G1 Series















































































































































Search results

Summary of Contents for G1 Series

Reviews:

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 25 / 142

Search results

Summary of Contents for G1 Series

Reviews: