Culligan G1 Series Installation, Operation And Service Instructions Download Page 14

Page: 14 / 142

Culligan® Series G1 Reverse Osmosis

Cat. No. 01021713

4. Remove a new membrane from its plastic bag. Lightly lubricate the O-rings with a silicone-based lubricant or

use a mixture of 70% glycerin and 30% water.

CAUTION! Do not use a petroleum-based lubricant. It will damage the synthetic rubber and the

membrane.

5. Install the membrane in the same direction as indicated by the arrow on the outside of the membrane vessel.

The brine seal end should go in last.

6. Repeat for the remaining membrane housings. There may be from one to four housings on each model.

G1 Tubing Configuration

FROM MEMBRANE
CONCENTRATE 3/8" TUBE

SYSTEM PRODUCT
OUTLET 1/2" TUBE

SYSTEM INLET

1/2" TUBE

SYSTEM WASTE
(CONCENTRATE) 3/8" TUBE

FROM MEMBRANE
PRODUCT 1/2" TUBE

TO MEMBRANE

FEED (1/2" TUBE)

Figure 9. G1 tubing configuration.

WARNING! The system must be grounded. An improperly grounded unit could cause injury from

electrical shock!

Summary of Contents for G1 Series















































































































































Search results

Summary of Contents for G1 Series

Reviews:

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 14 / 142

Search results

Summary of Contents for G1 Series

Reviews: