manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 13 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 13

G1 RO Installation    

9

Cat. No. 01021713

Feed Flow Meter

1.  Install the feed flow meter on the prefilter.
2.  Install the flow meter cable.

1

2

Figure 7. Feed flow meter installed on prefilter. 

Membranes

Before mounting the membrane housings, the membranes must be inserted into the housings. Take care to not damage 

the end cap O-rings or membrane brine seal.
The membranes are shipped in a sealed package. Use extreme caution when opening the package with a sharp instru-

ment. Any damage to the membrane can cause poor quality coming from the unit.

1.  The membrane housings have directional arrows on them that indicate direction of flow. Install the membranes 

in the direction of flow. Open the housing end opposite the direction of flow.

2.  Remove the end caps from all vessels by removing the two Allen head screws that hold down the retaining 

clips. The clips are pushed into an internal groove in the housing, so completely remove the screws so the clip 

can be slid out of the groove. Note placement of the caps to assure reinstallation in the same orientation.

3.  Check the O-ring seals on the membrane and end plug, and the membrane brine seal for damage. If an O-ring 

is cut or crimped, it may cause high flow and poor quality. Replace any suspicious O-rings. 

End Cap

Retaining Rings

Screws

O-Rings

FLOW

Membrane

Brine Seal

Housing

Figure 8.  Membrane and its housing.

Summary of Contents for G1 Series















































































































































Reviews:

No comments