manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 116 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 116

 112 

  

Culligan® Series G1 Reverse Osmosis

 112 

 

Cat. No. 01021713

International Drain Assembly with Fast Flush Solenoid Valve 

6

1

5

4

10

3

9

14

11

13

12

2

7

8

15

13

16

18

19

17

Out To Drain

To Return

Assembly

From Last Membrane 

(Concentrate)

Figure 64. 

G1 drain assembly with fast flush solenoid valve.

Item Part  No.

Description

Qty

01024239 Assembly, Drain w/220V Solenoid Flush (items 1–18)

1

01022013 Needle Valve, 1/4" FNPT, Brass

2

2

—

Nipple, 1/4 x Close, PVC Sch. 80, TBE

1

3

—

Tee, 3/8", Socket, PVC Sch. 80

2

4

—

Bushing, 3/8 x 1/4, SxT, PVC Sch. 80

2

5

—

Pipe, 3/8", Sch. 80, Length 1.75"

2

6

—

Elbow, 3/8 SxT, PVC Sch. 80

1

7

—

Bushing, 1/2 x 3/8, TxT, PVC Sch. 80

1

8

—

Nipple, 3/8 x Close, PVC Sch. 80, TBE

1

9

—

Bushing, 3/8 x 1/4, SxS, PVC Sch. 80

1

10

—

Fitting, Male Adapter, 3/8T x 1/4 NPTE, PI

2

11

—

Fitting, Union Tee, 3/8T, PI

1

12

—

Tube, 3/8", cut length 3"

1

13

—

Tube, 3/8", cut length 2"

2

14

—

Nipple, 1/4 x 1-3/4, PVC Sch. 80, TOE

1

15

—

Stem Adapter, 1/4NPT x 3/8 Stem, Polypropylene

1

16

—

Fitting, Male Adapter, 3/8 x 1/2 NPTE, PI

1

17

—

Fitting, Union Elbow, 3/8T, PI

1

18

01022601 Solenoid Assembly, 1/2", 220V/50Hz

1

—

01024635 Coil, Solenoid, Repl, 220–240/50–60

1

19

01025739 Cable, Solenoid

1

Summary of Contents for G1 Series















































































































































Reviews:

No comments