PG-36702
Quick Reference
SETUP
Guide
Troubleshooting
2.
1.
3.
5.
4.
6.
Fully immerse the charcoal water filter in cold tap
water and soak for 15 minutes. Flush filter by running
cold tap water through holes in bottom of compartment
for 10 seconds (see complete instructions on page 8 of
your instruction booklet). Insert the filter into the water
filter holder. Open the water reservoir and place filter
holder into the unit.
Pour your desired amount of water into the
water reservoir. A water level indicator is
located on the side of the unit.
Helpful Hint:
“Pre-heat” your carafe by
rinsing it out with hot water before brewing.
Open the filter basket door by pressing the
Release button, and insert a paper filter or
permanent filter into the filter basket holder.
Replace the cover, and close door.
Remove hopper lid, fill with beans,
and replace the lid.
To start grinding & brewing, press the BREW
button. Once the coffee has finished brewing,
five beeps will sound. The unit will
immediately shut off. The thermal carafe will
keep coffee hot for hours.
Press the ON/OFF button to turn on the coffeemaker.
Select the amount of cups you wish to brew by turning
the Grind Control knob. Select your desired coffee
strength by pressing the Strength button. Your selected
coffee strength will be indicated in the bar on the LCD
display.
IMPORTANT
Do not throw away. Read before operating your new
Brewing System. Keep for future reference.
These helpful hints are intended to be a supplement to the Instruction Booklet. In order to ensure
safe operation and optimum performance, please read the entire Instruction Booklet.
Fully Automatic Burr Grind & Brew
™
Thermal Coffeemaker
© 2017 Cuisinart
BEFORE FIRST USE
Before using your Cuisinart
®
Fully Automatic Burr Grind & Brew™ Thermal Coffeemaker for the
first time: BE SURE TO REMOVE POLYBAGS FROM CARAFE AND COFFEEMAKER. PLACE CARAFE BACK
ONTO BASE. During the manufacturing process, dust can get trapped in your coffeemaker. We recommend
flushing out the system before brewing your first pot of coffee. Simply follow “Making Coffee with Pre-
Ground Beans,” page 10 in the Instruction Booklet. Skip step #1 and be sure to use only water and a paper
filter…no coffee! Once you’ve done that, brew a pot of real coffee and get ready to enjoy Cuisinart at its best!
PROBLEM
CAUSE
SOLUTION
The coffeemaker
is beeping
Filter door is not closed
• Check to be sure that all components of the filter compartment
are in place
• Close filter door (you will hear a click if the door is properly shut)
Filter basket is not in
place
• Open filter door by pressing the filter door Release button
• Hook filter basket with cover onto door
• Close filter door (you will hear a click if the door is properly shut)
Coffee grounds and filter
from previous use are
still in filter basket
• Remove filter and used coffee grounds
• Add new filter
The brew cycle
will not start
There is no water in the
water reservoir
• Fill the water reservoir using the water level markings
Coffee is weaker
than usual
There are not enough
beans in the hopper
• Be sure there are enough beans in your hopper for the amount of
coffee you intend to brew
Strength setting
is incorrect
• Check your strength setting — displayed on the LCD screen
• To change your strength setting, press the Strength Control button
The coffeemaker
is not grinding
beans
The hopper may be
too full
• Turn the coffeemaker off and unplug
• Remove some of the beans from the hopper
EMPTY
appears in LCD
display
Coffee grounds and filter
from previous use are
still in filter basket
• Remove filter and used coffee grounds
• Add new filter
CLEAN is flashing
on the LCD
when the unit
is turned on
Coffeemaker needs
to be decalcified
• Run a clean cycle – follow the decalcification directions on
page 11 of Instruction Booklet
The coffeemaker
will not enter
CLEAN mode
The water reservoir
is empty
• Fill the water reservoir with decalcification mixture before turning
the coffeemaker on - Follow the decalcification directions on
page 11 of Instruction Booklet
