CUBEX SKYMASTER III- 3B Manual Download Page 1

INSTRUCTIONS:  

CUBEX -SkyMaster Series 

 

 

Cubex Co., Inc. 

  

05-06 Rev 0

 

 

 

CUBEX  

Quad Antennas

 

 

SKYMASTER III– 3B 
SKYMASTER III– 5B 

3 Element ; 3 and 5 band Quad 

 

Plus 6 meters 

 
 

Safety warning 

 
Please read through these instructions completely before 
starting your installation. 
Antenna work is dangerous. Always wear an OSHA approved 
safety harness with the appropriate nylon or wire rope safety 
lanyards to protect yourself and your helpers from falls.  Also all 
helpers on the ground should be wearing hard hats to protect 
them from falling objects such as tools etc.  

 
 
 
 
 

Cubex Co., Inc. has no control over the conditions at the antenna site and therefore 
can not be held responsible for any damage or injury to persons or property. 
 
If for any reason you do not understand any part of these instructions, or your 
installation is different and these instructions do not pertain to your situation.  Do not 
hesitate to call Cubex Co., Inc. for assistance at (561) 748-2830; or email: 
[email protected] 

 

Note: Take precautions when handling and further processing fiberglass material.  It 
is recommended that gloves and dust mask be used when cutting and drilling this 
material.

 

 

 
 
Price: $ 4.95 US

 

Summary of Contents for SKYMASTER III- 3B














Reviews: