Cub Cadet LTX 1045 Operator'S Manual Download Page 33

FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT 

YOUR WARRANTY RIGHTS AND OBLIGATIONS

MTD Consumer Group Inc, the United States Environmental Protection Agency (EPA), and, for those products certified for sale in the state of 

California, the California Air Resources Board (CARB) are pleased to explain the emission (evaporative and/or exhaust) control system (ECS) 

warranty on your outdoor 2006 and later small off-road spark-ignited engine and equipment (outdoor equipment engine) In California, new 

outdoor equipment engines must be designed, built and equipped to meet the State’s stringent anti-smog standards (in other states, 1997 and 

later model year equipment must be designed, built, and equipped to meet the U.S. EPA small off-road, spark ignition engine regulations. MTD 

Consumer Group Inc must warrant the ECS on your outdoor equipment engine for the period of time listed below provided there has been no 

abuse, neglect or improper maintenance of outdoor equipment engine.
Your ECS may include parts such as the carburetor, fuel-injection system, the ignition system, catalytic converter, fuel tanks, fuel lines, fuel caps, 

valves, canisters, filters, vapor hoses, clamps, connectors, and other associated emission-related components.
Where a warrantable condition exists, MTD Consumer Group Inc will repair your outdoor equipment engine at no cost to you including 

diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

This emission control system is warranted for two years. If any emission-related part on your outdoor equipment engine is defective, the part 

will be repaired or replaced by MTD CONSUMER GROUP INC.

OWNER’S WARRANTY RESPONSIBILITIES:

As the outdoor equipment engine owner, you are responsible for performance of the required maintenance listed in your owner’s manual. MTD 

Consumer Group Inc recommends that you retain all receipts covering maintenance on your outdoor equipment engine, but MTD Consumer 

Group Inc cannot deny warranty solely for the lack of receipts.
As the outdoor equipment engine owner, you should however be aware that MTD Consumer Group Inc may deny you warranty coverage if 

your outdoor equipment engine or a part has failed due to abuse, neglect, or improper maintenance or unapproved modifications.

You are responsible for presenting your outdoor equipment engine to MTD Consumer Group Inc’s distribution center or service center as soon 

as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question 

regarding your warranty coverage, you should contact the MTD Consumer Group Inc Service Department at 1-800-800-7310 or via email at 

http://support.mtdproducts.com

GENERAL EMISSIONS WARRANTY COVERAGE:

MTD Consumer Group Inc warrants to the ultimate purchaser and each subsequent purchaser that the outdoor equipment engine is: Designed, 

built and equipped so as to conform with all applicable regulations; and free from defects in materials and workmanship that cause the failure 

of a warranted part to be identical in all material respects to that part as described in MTD Consumer Group Inc’s application for certification.

The warranty period begins on the date the outdoor equipment engine is delivered to an ultimate purchaser or first placed into service. The 

warranty period is two years.
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:

1. 

Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied, is warranted for 

the warranty period stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by MTD 

Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the 

remainder of the period.

2. 

Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period 

stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.

3. 

Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the 

period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the part 

will be repaired or replaced by MTD Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under 

warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part.

4. 

Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge 

to the owner.

5. 

Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to 

service the subject engines or equipment.

6. 

The outdoor equipment engine owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, 

emission-related warranted part, provided that such diagnostic work is performed at a warranty station.

7. 

MTD Consumer Group Inc is liable for damages to other engine or equipment components proximately caused by a failure under 

warranty of any warranted part.

8. 

Throughout the off-road engine and equipment warranty period stated above, MTD Consumer Group Inc will maintain a supply of 

warranted parts sufficient to meet the expected demand for such parts.

9. 

Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to 

the owner. Such use will not reduce the warranty obligations of MTD Consumer Group Inc.

Summary of Contents for LTX 1045









































































Reviews: