background image

58

CUB CADET CORPORATION

MANUFACTURER’S ONE YEAR LIMITED WARRANTY

(COMMERCIAL USE)

The limited warranty set forth below is given by CUB CADET
LLC (“CUB CADET”) with respect to new merchandise
purchased and used in the United States, its possessions and
territories.

CUB CADET warrants this product against defects in material
and workmanship for a period of one (1) year for commercial
users, commencing on the date of original purchase and will,
at its option, repair or replace, free of charge, any part found
to be defective in material or workmanship. This limited
warranty shall only apply if this product has been operated
and maintained in accordance with the Operator’s Manual
furnished with the product, and has not been subject to
misuse, abuse, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water or damage because of
other peril or natural disaster. Damage resulting from the
installation or use of any part,  accessory or attachment not
approved by Cub Cadet for use with the product(s) covered
by this manual will void your warranty as to any resulting
damage.

Batteries and belts are subject to separate terms as follows:

a.

Batteries have a one-year prorated limited warranty
with 100% replacement during the first three
months. After three months, the battery replacement
credit is based on the months remaining in the
twelve (12) month period dating back to the original
date of sale. Any replacement battery will be
warranted only for the remainder of the original
warranty period.

b.

All belts are covered by a one (1) year limited
warranty against defects in material and
workmanship.

HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, THROUGH YOUR LOCAL
AUTHORIZED CUB CADET DEALER. To locate the dealer in
your area, please check for a listing in the Yellow Pages or
contact Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio
44136-0019, or call 1-877-282-8684, or log on to our Web site
at www.cubcadet.com.

This limited warranty does not provide coverage in
the following cases
:

a.

Routine maintenance items such as lubricants, filters,
tune-ups, or adjustments such as brake adjustments,
or clutch adjustments; and normal deterioration of the
exterior finish due to use or exposure.

b.

Normal wear parts or components, including
batteries, belts, seats and tires.

c.

CUB CADET does not extend any warranty for
products sold or exported outside of the United
States of America, its possessions and territories,
except those sold through CUB CADET’S
authorized channels of export distribution.

d.

Replacement parts that  are not genuine Cub Cadet
parts.

e.

Service completed by someone other than an
authorized service dealer.

No implied warranty, including any implied warranty of
merchantability or fitness for a particular purpose,
applies after the applicable period of express written
warranty above. No other express warranty or guaranty,
whether written or oral, except as mentioned above,
given by any person or entity, including the dealer, with
respect to any product shall bind CUB CADET. During
the period of the Warranty, the exclusive remedy is repair
or replacement of the product as set forth above.
 (Some
states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.)

The provisions as set forth in this Warranty provide the
sole and exclusive remedy arising from the sale. CUB
CADET shall not be liable for incidental or
consequential loss or damages including, without
limitation, to any claim for loss of profits, loss of
savings or revenue, loss of the use of the equipment or
any associated equipment, facilities or service,
downtime, the claims or costs of third parties including
customers, and injury to property, and further
including expenses incurred for substitute or
replacement lawn care services, for transportation or
for related expenses, or for rental expenses to
temporarily replace a warranted product
. (Some states
do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion may not
apply to you.)

In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of the safety features of the product shall void this Warranty.
You assume the risk and liability for loss, damage, or injury to
you and your property and/or to others and their property
arising out of the use or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than
the original purchaser or original lessee.

How State Law Relates to this Warranty: This limited
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.

                      IMPORTANT: Owner must present Original Proof of Purchase to obtain warranty coverage.

                               

Cub Cadet LLC, P.O. BOX 361131 CLEVELAND,OHIO 44136-0019; Phone: 1-877-282-8684

Summary of Contents for LT 2138





























































Reviews: