Cub Cadet LT 2138 Page 57 Operator'S Manual Download | Manualshive

Page: 57 / 60

background image

57

LT 3128

2-1/8 gallons

4 pints

6 qts.

0 to 5.5 mph

0 to 3 mph

Kohler Command

16 HP

1

3.55 in.
2.64 in.

26.0

1200 RPM

3600 RPM ± 75

Battery

.030 in.

12 volt neg. ground

725-1706

15 amp regulated

25 amp

725-0963

Internal expanding

15 x 6-6
20 x 9-8

30.00 in.
27.50 in.
47.00 in.
72.00 in.
51.00 in.
42.00 in.

6.00 in.

26.50 in.

CAPACITIES

Fuel Tank ........................................................................
Crankcase (approximately) .............................................
Transmission Case (approximately) ................................
HYDROSTATIC DRIVE
Speed: Forward................................................................

Reverse ................................................................

ENGINE

Make and Model ..............................................................
Horsepower .....................................................................
Cylinders .........................................................................
Bore .................................................................................
Stroke ..............................................................................
Displacement (cubic inches) ...........................................
Engine Speed (governed)

Low Speed ...................................................................
High Speed (no load) ...................................................

Ignition .............................................................................
Spark Plug Gap (Cub Cadet No. 759-3336) ....................

ELECTRICAL SYSTEM

System Voltage ...............................................................
Battery .............................................................................
Alternator .........................................................................
Fuse (auto type) ..............................................................
Head Lamp Bulb ..............................................................

BRAKES ............................................................................
TIRE SIZES

Front ...............................................................................
Rear .................................................................................

DIMENSIONS

Tread:

Front with 15 x 6-6 tires ................................................
Rear with 20 x 9-8 tires ................................................

Wheelbase ......................................................................
Length, over all ................................................................
Width, over all (w/ mower deck - chute up)  .....................
Height, over all (to top of steering wheel) ........................
Ground Clearance  ...........................................................
Turning Radius  ................................................................

SPECIFICATIONS

Specifications are subject to change without notice.

«
...
55
56
57
58
59
...
»

Summary of Contents for LT 2138





























































Reviews:

No comments

Related manuals for LT 2138

PowerMax 1200/32

Brand: Gardena Pages: 352

Brand: Gardif Pages: 21

Brand: Yard Machines Pages: 72

Brand: Qualcast Pages: 16

MULTICLIP MULTICLIP 46 S SVAN

Brand: Stiga Pages: 2

Brand: Cub Cadet Pages: 19

Brand: Gardenline Pages: 36

Brand: Jacobsen Pages: 98

Brand: Cub Cadet Pages: 44

Brand: Agri-Fab Pages: 24

COLLECTOR 53 SE COMBI 53 SE COMBI

Brand: Stiga Pages: 2

Brand: Ariens Pages: 26

Brand: Cub Cadet Pages: 48

Brand: California Trimmer Pages: 8

Brand: MTD Pages: 31

Brand: Cub Cadet Pages: 52

Brand: Husqvarna Pages: 50

Brand: Husqvarna Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands