Crown Audio, Inc.
P.O. Box 1000
Elkhart, IN 46515-1000
TEL: 574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
SST-SX
4-03 132300-1A
S Y S T E M S O L U T I O N T O P O L O G I E S
Crown’s Three-Year, No-Fault, Full Warranty
Crown offers a Three-Year, No-Fault, Full Warranty for every new Crown amplifi er product—an
unsurpassed industry standard. With this unprecedented No-Fault protection, your new Crown ampli-
fi er product is warranted to meet or exceed original specifi cations for the fi rst three years of ownership.
During this time, if your unit fails, or does not perform to original specifi cations, it will be repaired or
replaced at our expense. About the only things not covered by this warranty are those losses normally
covered by insurance and those caused by intentional abuse. And the coverage is transferable, should
you sell your unit.
See your authorized Crown dealer for full warranty disclosure and details. For customers outside of the
USA, please contact your authorized Crown distributor for warranty information or call 574-294-8200.
T
he Crown SST-SX module is a fourth-order
Linkwitz-Riley type crossover with the
crossover point switchable to either 80 or
120 Hz. High-frequency (HF) signals are routed to
the internal amplifer channels, and low-frequency
(LF) signals are summed and routed the mono
output connector. Truly a professional crossover,
the SST-SX uses hard-wired precision compo-
nents that stay at the frequencies you have
selected for consistent bandwidth control.
SST (System Solution Topologies) modules install
into the back of Crown SST-compatible amplifi ers,
saving rack space and simplifying system wiring.
For more details about the Crown SST-SX, con-
tact the Crown Technical Support Group at
800-342-6939 or
574
-294-8200. Also, visit the
Crown Audio website at www.crownaudio.com.
Specifi cations
Note: Specifi cations describe typical results using the
SST-SX crossover module installed in a Crown SST-
compatible amplifi er. All measurements are in Stereo
mode with 8-ohm loads and an input sensitivity of
26-dB gain at 1-kHz rated power unless otherwise
specifi ed. Specifi cations for units supplied outside
the U.S.A. may vary slightly at different AC voltages
and frequencies.
Performance
Frequency Response:
±0.1 dB from 20 Hz to 20
kHz at 1 watt.
Signal to Noise Ratio,
A-Weighted: Better than 105 dB below rated 1-kHz
power;
20 Hz to 20 kHz: Better than 100 dB below rated
1-kHz power.
Total Harmonic Distortion (THD):
1-kHz rated
power, 1.0% or less true THD from 20 Hz to 20
kHz.
Crosstalk:
Better than 50 dB below rated power,
20 Hz to 20 kHz.
Input/Output
Input Impedance:
Nominally 20 k ohms, balanced. Nominally 10 k
ohms, unbalanced.
Output Impedance:
600 ohms, balanced.
Maximum Output:
+15 dBm into 600 ohms.
Specifi cations subject to change without prior notice. Latest
information available at www.crownaudio.com.
Crown is a registered trademark of Crown International, Inc.
Other trademarks are the property of their respective owners.
Printed in U.S.A.
© 2003 Crown Audio, Inc.
Features
• Stereo biamp.
• 24-dB/octave Linkwitz-Riley tuned fi lters.
• Crossover switchable to either 80 or 120 Hz.
• SST modules install into the back of your
amplifi er, saving rack space and simplifying
system wiring.
• Neutrik® Combo (¼-inch (6.35-mm) phone
and 3-pin XLR) input jacks.
• Male 3-pin XLR Sub Output.
• Optional high-pass fi lter bypass on amplifi ed
outputs adapts system for full-range use.
• SST Modules add fl exibility by allowing you to
tailor your Crown Contractor (CH/CL) Series
or CE Series amplifi er to your application.
SST-SX Block Diagram
80 / 120 Hz HP
24 dB/oct. slope
80 Hz
120 Hz
80 / 120 Hz LP
24 dB/oct. slope
80 / 120 Hz HP
24 dB/oct. slope
80 Hz
120 Hz
80 / 120 Hz LP
24 dB/oct. slope
OUT
IN
BYPASS
OUT
IN
BYPASS
HOST
AMPLIFIER
CH1 INPUT
HOST
AMPLIFIER
CH2 INPUT
SUB OUT
(SUMMED)
CH1
CH2
3
2
1
3
2
1
