Crown CG-214 Installation And Operation Manual Download Page 21

Page: 21 / 22

INSTALLATION AND OPERATION MANUAL, GAS BOILERS,

MODELS CG-214(E), CG-314(E), CG-414(E), CG-220(E), CG-320(E), CG-325(E), CG-330(E)

PART NUMBER 10042R3

2005-12-19

8.0 TROUBLESHOOTING

BURNERS PRODUCE CARBON DEPOSITS

1. Wrong size orifices.

2. Burner air not adjusted properly.

3. Wrong gas supply.

4. Incorrect pressure at supply.

PILOT DOES NOT LIGHT

1. Gas supply to unit is OFF.

2. Power supply is OFF.

3. Gas control knob is OFF.

4. Dirty or loose wire connection to module - clean and/or tighten.

5. Ignitor cable, shorting out - check that not in contact with metal or damaged; may require

replacement.

6. Defective control or module.

7. Unit goes into 100% lockout - turn off and try again in five minutes.

8. Dirty flame sensor - clean with emery cloth.

9. Cracked ceramic insulator - replace pilot burner/ignitor sensor.

10.

Too much draft.

WARNING: The boiler and its parts are hot. Use care when operating,
cleaning, or servicing the boiler.

Summary of Contents for CG-214























Search results

Summary of Contents for CG-214

Reviews:

Related manuals for CG-214

Brands by name

Popular brands

Crown CG-214, Installation And Operation Manual

Search results

Summary of Contents for CG-214

Reviews:

Related manuals for CG-214

Brands by name

Popular brands