Crow Shepherd Installation Manual Download Page 6

Page: 6 / 73

thecrowgroup.com

Page | 5

Overview & Communication Capabilities

Front View

Led Indications

SYSTEM STATUS

LED INDICATION

System is armed

RED

System is in Arm process

RED Blink

Burglary Alarm

RED Blink

Panic Alarm

Led state no change

System is disarmed and Ready to Arm

Green

System is disarmed and NOT Ready to Arm

LED Off

Main power and Back up Battery are OK

Green Blink

Battery missing OR Battery in charge mode

Green / RED Blink

AC fail – system working on back up battery Mode

RED Blink

System working with main communication method

(Ethernet)

Green Blink

System working with backup communication method

(WIFI or GSM)

Green / RED Blink

No communication method

LED Off

Remote configuration connection

Green

WPS mode

Green

Blink

Green

Blink

Green

Blink

Summary of Contents for Shepherd










































































Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands

Crow Shepherd, Installation Manual

Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands