background image

CCpilot V700 

Revision: 1.0  

Technical Manual 

2020-09-10 

 

 

 

www.crosscontrol.com 

4

 

2.

 

Product models 

This documentation is applicable for all CCpilot V700 models. These models are: 

  CCpilot V700 standard version of product. Part number C000152-04 

  CCpilot V700 standard with Bluetooth module. Part number: C000152-01 

  CCpilot V700 custom version. Part number C000152-02. 

These models share the same level of performance, hardware architecture, TFT, enclosure 
and connectors. The PCB is the same for all versions but may be populated differently. 

2.1.1.

 

Customized models 

The platform enables additional customization of hardware and software. Described herein are 
the features included in product models described above. Additional features in customized 
models will be documented separately. 
Contact CrossControl for customization inquiries. 

2.2.

 

Document conventions 

This document uses the following conventions: 
Description 

Appearance 

Important information 
 
Differences between product 
models 

            (exclamation symbol) 
 
             (observe’ symbol) 

 
Text formats used in this document are described in the table below: 

Format

 

Use

 

Italics 

Names, designations, 

and 

references 

Bolded 

Important information 

2.3.

 

Identification 

Each device has identification labels with serial number, part number and revision which identifies 
your unique device. This information is required when communicating with CrossControl regarding 
Technical support and Service/Repair needs.  

 

 
 
 
 
 

Figure 1: Identification labels

 

Summary of Contents for CCpilot V700




























Reviews: