crosscontrol CCpilot V700 Technical Manual Download Page 25

Page: 25 / 27

CCpilot V700

Revision: 1.0

Technical Manual

2020-09-10

www.crosscontrol.com

75-400 44-55

54-65

400-1000 55

(1) Compliance to RF immunity and RF emission standards require use of shielded cables for Ethernet, USB and Video interfaces.

EMC tests are performed at 24 V

supply voltage unless other levels are specified in test

standards.
System level compliance to EMC standards may be affected by external factors like mounting,
omitting the use of shielded cables etc.

8.4.

Weight and dimensions

Attribute

Description

Comments

Dimensions

201 x 135 (140) x 40 mm

(W x H (H+connector) x D)

Weight

0.62kg

Mounting holes

Spacing

Thread dimension

Thread depth

RAM-202U

Dia 46 mm

8.0 mm

Enclosure material

PBT + PC plastic, impact

modified and flame

retarted

Figure 6: CCpilot V700 dimensions.

Summary of Contents for CCpilot V700




























Search results

Summary of Contents for CCpilot V700

Reviews:

Related manuals for CCpilot V700

Brands by name

Popular brands

crosscontrol CCpilot V700, Technical Manual

Search results

Summary of Contents for CCpilot V700

Reviews:

Related manuals for CCpilot V700

Brands by name

Popular brands