manualshive.com logo in svg

Crestron TSW-570P, Product Manual

Share
Download
Crestron TSW-570P Product Manual Download Page 165

Product Manual — Doc. 8550E

TSW-70 Series • 159

Bluetooth Beacon

Tap BLE Beacon on the Setup screen to display the BLE Beacon screen. (TSW-770 and
TSW-1070 only)

BLE Beacon Screen

Use the BLE Beacon screen to configure the built-in PinPoint™ proximity detection beacon. Using
Bluetooth® technology, the beacon works with the Crestron App or Crestron PinPoint App to
determine when a mobile device is in or near the same room as the beacon, and signals the
mobile app to automatically display the appropriate controls and information for the room.

l

Tap On or Off underneath BLE Beacon to turn the proximity beacon on or off, respectively.

l

Tap On or Off underneath Config Mode to turn configuration mode on or off, respectively.
Turning on configuration mode enables the proximity beacon to be configured.

NOTE: 

The proximity beacon and configuration mode cannot both be turned on at the same

time.

Tap < BACK to return to the Setup screen.

Summary of Contents for TSW-570P



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands