Home
/
Crestron
/
TSW-570P
/
Product Manual

Crestron TSW-570P, Product Manual

Share

Page: 102 / 226

Crestron TSW-570P Product Manual Download Page 102

96 • TSW-70 Series

Product Manual — Doc. 8550E

TSW-570, TSW-770, and TSW-1070
Installation

Use the following procedures to install the TSW-570, TSW-770, and TSW-1070 touch screens.

Install the Mounting Bracket

The TSW-570 uses a different mounting bracket than the TSW-770 or TSW-1070. The
procedures for installing each mounting bracket are described in the following sections.

Install the TSW-570 Mounting Bracket

The TSW-570 can be mounted into drywall and other surfaces, or it can be mounted onto a wall
stud.

NOTE:

Additional mounting options are possible using the TSW-UMB-70 universal mounting

bracket, TSW-UMB-70-PMK preconstruction mounting kit, TSW-UMB-70-BBI wall mount back
box, or TSW-570/770-RMK-1 rack mount kit. For more information, refer to the product pages
at

www.crestron.com

Preconstruction Installations

To install the TSW-570 mounting bracket in preconstruction applications, use standard drywall
nails or screws (not included) to attach the TSW-UMB-70-PMK mounting bracket to a wall stud.

NOTE:

Allow an air gap of at least 12 in. (305 mm) in the wall cavity above and below the touch

screen for heat dissipation.

Postconstruction Installations

To install the TSW-570 mounting bracket in postconstruction applications:

1. Use the TSW-UMB-70-PMK mounting bracket as a cutout template by turning the bracket

to face the wall, ensuring it is level, and tacking it to the wall temporarily with finishing
nails (not included) through the smaller holes around the cutout opening.

«
...
100
101
102
103
104
...
»

Summary of Contents for TSW-570P



































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands