Crestron TSW-560-LB Quick Start Download Page 1

Quick Start

The Crestron® TSW-560-LB is a room availability light bar for the Crestron TSW-560,  

TSW-560P, and TSW-560-NC touch screens. When the light bar is installed onto a touch screen 

as part of an enterprise room scheduling solution, the light bar illuminates to indicate the room’s 

availability.

Check the Box

Item

Qty

TSW-560-LB-B or TSW-560-LB-W

1

Light Bar, 5 in., Black or Light Bar, 5 in., White

1

Screw, 04-40 x 1-1/2 in., Undercut Head, Phillips (P/N 2037906)

2

Screw, 04-40 x 3/8 in., Undercut Head, Phillips (P/N 2007173)

2

Refer to the TSW-560-LB-B and TSW-560-LB-W product page at 

www.crestron.com

 for a complete list of 

color and texture variations.

Install the TSW-560-LB

Use the following procedures to install the TSW-560-LB as part of a new or existing TSW-560 

installation.

NOTE: 

For portrait touch screens (such as the TSW-560P), the TSW-560-LB may be installed 

vertically using the same procedures required for a landscape touch screen installation.

Install the Light Bar Assembly

1. 

If the TSW-560-LB is being added to an existing TSW-560 installation, pull the TSW-560 

carefully out of its mounting bracket and disconnect the Ethernet cable.

NOTE: 

If the TSW-560 is secured to the mounting bracket with a security latch, refer to 

the removal procedure described in the TSW-560/TSW-760/TSW-1060 Quick Start 

(Doc. 7926) at 

www.crestron.com/manuals

.

2. 

Use the two included 4-40 x 3/8 in. screws to attach the light bar assembly to the rear of 

the TSW-560.

 

Light bar

assembly

Screw (2):

4-40 x 3/8 in.

USB connector

Touch screen

USB port 

3. 

Insert the assembly’s USB connector into the USB port on the rear of the touch screen.

Attach the Light Bar to the Mounting Bracket

1. 

Loosen the two pan head 4-40 x 1-1/2 in. screws on the TSW-560 mounting bracket.

2. 

If installed, remove the mounting bracket from the mounting surface as shown in the 

following illustration.

 

Pull the top surface 

up and out of the 

mounting hole

TSW-560

mounting bracket

(side view)

Loosen both of the 

pan head screws

3. 

Separate the two halves of the mounting bracket by removing the two pan head 1-1/2 in. 

screws. These screws are not used in this installation.

4. 

Align the light bar in between the two halves of the mounting bracket as shown in the 

illustration below.

5. 

Attach the light bar to the front half of the mounting bracket, and then reconnect the two 

halves of the mounting bracket.

NOTE: 

Pull the flex circuit attached to the light bar through the opening in the mounting 

bracket after the light bar is attached to the mounting bracket.

6. 

Use the two included flat head 4-40 x 1-1/2 in. screws to secure the light bar to the 

mounting bracket. Do not tighten the screws fully.

 

Screw (2): 

4-40 x 1-1/2 in.

flat head

Flex circuit

TSW-560

mounting bracket

(front half)

Light bar

TSW-560

mounting bracket

(rear half)

NOTE: 

Do not use the pan head 4-40 x 1/2 in. screws that come with the TSW-560 

mounting bracket for the light bar installation. The flat head 4-40 x 1/2 in. screws that 

come with the light bar must be used instead.

7. 

Insert the mounting bracket, bottom side first, back into the mounting surface.

8. 

Push the rear half of the mounting bracket back so that it is seated behind the mounting 

surface completely.

9. 

Tighten the two flat head  4-40 x 1-1/2 in. screws to secure the bracket to the mounting 

surface.

Attach the Light Bar to the TS-5-MSMK

The light bar may also be attached to the TS-5-MSMK multisurface mounting kit for 

applications where the touch screen will be mounted to a flat pane of glass or a similar 

smooth surface (such as granite, marble, plaster, or smooth stone and masonry). For more 

information on installing the TS-5-MSMK, refer to the TS-5-MSMK Quick Start (Doc. 8427) at 

www.crestron.com/manuals

.

The following supplies (not included) are required for this installation: a level, a roll of tape, a 

Phillips screwdriver, and a surface cleaning product that does not leave a residue.

Attach the TS-5-MSMK Mounting Plate to the Surface

1. 

Clean and dry the mounting surface thoroughly.

2. 

Use a level to tape a horizontal reference line to the surface to align with the lower edge of 

the mounting plate.

3. 

Remove the protective covering from the rear of the TS-5-MSMK mounting plate.

CAUTION: 

The adhesive on the rear of the mounting plate is high-strength bond. Once the 

adhesive comes in contact with a surface, it cannot be removed easily.

4. 

Hold the mounting plate at a 45-degree angle to the surface, and then carefully align the 

lower edge of the pad with the taped reference line. Do not allow the adhesive to come in 

contact with the surface.

5. 

Attach the mounting plate to the surface, starting with the bottom edge near the taped 

reference line. Press the pad to the surface firmly to ensure proper adhesion and to 

eliminate any trapped air bubbles.

 

Mounting plate

Glass surface

TSW-560-LB

Room Availability Light Bar for TSW-560, TSW-560P, and TSW-560-NC

Reviews: