background image

Crestron 

ST-1550 & ST-1550C

 

SmarTouch STS Touchpanels

 

interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.  

 

Consult the dealer or an experienced radio/TV technician for help.  

As of the date of manufacture, the unit has been tested and found to comply with 
specifications for CE marking. 

 

Recommended Touchpanel Cleaning 

Keep the surface of the touchscreen free of dirt, dust, or other materials that could 
degrade optical properties. Long term contact with abrasive materials can scratch the 
surface which may detrimentally affect image quality. 

For best cleaning results, use a clean, damp, non-abrasive cloth with any 
commercially available non-ammonia glass cleaner. Surrounding plastic enclosure 
may not provide a complete water-tight seal. Therefore, apply cleaning solution to 
the cloth rather than the surface of the touchscreen. Wipe touchscreen clean and 
avoid ingress of moisture beneath panels.  

Applying Power 

The touchpanel can be powered via an external AC power pack, while resting in the 
ST-DS, or via the ST-BTP. Each of these supplied items have their own Operations 
Guides which details proper usage. Refer to the table below for the required 
document number. This table does not account for the latest revision letter of each 
document.  

Devices that Power the SmarTouch STS Touchpanel 

POWER OPTION

NOMENCLATURE

DOCUMENT 

NUMBER

Domestic External AC Power Pack

PW-1210

5762

International External AC Power Pack

PWI-1210

5763

Docking Station

ST-DS

5738

Battery Pack

ST-BTP

5746

 

Configuring the Touchpanel 

It may be necessary to make adjustments or 

configure

 your touchpanel due to 

personal preference or the way you would like to use it. If you are uncomfortable 
with making these adjustments yourself, consult the dealer in your area.  

User's Operations Guide - DOC. 5804 

SmarTouch STS  

  3 

Summary of Contents for SmarTouch STS ST-1550





















Reviews: