Crestron ML-500 Programming Manual Download Page 7 | Manualshive

Page: 7 / 30

Crestron ML-500 Programming Manual Download Page 7

Crestron

ML-500

Mini LCD RF Wireless Handheld Remote

ML-500 Memory Structure

Each of the 34 labeled buttons (hard keys) on the remote can be independently
programmed for the MAIN page and each Grp group. Additionally, each Grp group
can use the 10 soft keys that flank the LCD to access up to 40 additional functions
that can be programmed within the Grp group. For example, the hard keys in MAIN
can be programmed to control a receiver while the hard keys in Grp group 8 can be
programmed to control a DVD player. Similarly, soft keys can be independently
programmed for each Grp group.

The ML-500 can also be programmed with up to 50 “Favorite” functions. Favorites
can be defined for any control system operation such as switching to a preset radio
station or adjusting lighting to a preset level. These Favorites are independent of the
MAIN page and Grp groups and can be programmed for any device controlled by the
control system. Additionally, a press of a Favorite button can be programmed to
jump the LCD to a page within any Grp group.

NOTE:

The ML-500 can send commands to the Crestron MC2W control system or

to any other Crestron control system via the Crestron CNRFGWA-418 1-Way RF
Receiver.

Navigation

To view all of the available soft key functions within a Grp group or list of Favorites,
the user must use the menu navigation keys located below the LCD. The following
sections describe menu navigation for Grp groups and Favorites.

Grp Group Navigation

Navigating within a Grp group allows the user to view soft key functions that are
programmed within a Grp group. For example, a Grp group that controls a specific
room may have soft keys programmed for lighting or HVAC control. While viewing
a Grp group, the user can view a list of up to 40 functions spread over four pages by
pressing the

PAGE

button. Additionally, the 34 hard keys will function as

programmed for the Grp group.

The following diagram shows how a soft key press from the MAIN page flips the
LCD to the first page of soft keys in a Grp group named THTR. Pressing

PAGE

will

show the user all of the programmed soft key functions for the THTR group.

Programming Guide – DOC. 6263

Mini LCD RF Wireless Handheld Remote: ML-500

•

3

«
...
5
6
7
8
9
...
»

Summary of Contents for ML-500































Reviews:

No comments