Crestron Green Light GL-IPAC-SW8 Product Manual Download Page 32 | Manualshive

Page: 32 / 45

background image

Product Manual — Doc. 7389C

GL-IPAC-SW8 • 32

3. Press OK to save assignments.

Photocell Assignments Screen

Keypads

Keypads configures all keypads in the system. A total of 16 external keypads can be connected to
the GL-IPAC-SW8.

To configure keypads:

1. Select Keypads from the Setup menu.

2. Press Find to begin the keypad search process.

3. Find the keypad by pressing any button on the keypad or by entering the keypad’s serial

number. Note that all buttons flash if opting to find a keypad by pressing one of its
buttons. Once a button on a flashing keypad is pressed, the keypad is identified by the
GL-IPAC-SW8 and assigned an ID number. If Online is displayed, the GL-IPAC-SW8 found
the keypad. If Not Found is displayed, the GL-IPAC-SW8 cannot find the keypad.

Keypd List Screen

Keypad functions can be assigned automatically or manually:

l

Press assigns functions to the pressed button automatically.

l

Edit assigns functions manually.

4. Use ▼ and ▲ to highlight one of the keypads that is marked Online. When an Online

keypad is selected, the Find button changes to the ID button.

5. Press the ID button to locate the keypad; the keypad blinks until a button is pressed.

Keypd List Screen

«
...
30
31
32
33
34
...
»

Summary of Contents for Green Light GL-IPAC-SW8














































Reviews:

No comments

Related manuals for Green Light GL-IPAC-SW8

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 142

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 168

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 29

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 9

Brand: Warren Controls Pages: 16

Brand: Abus Pages: 12

ESD-5550 Series

Brand: GAC Pages: 12

XP-9 88-IoT Series

Brand: ICP DAS USA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands